Pulse Performance Products ATV QUAD Owner's Manual

Electric quad

Hide thumbs

Table Of Contents

ELECTRIC QUAD

OWNER'S MANUAL

FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™

•

ATV QUAD

DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS?

CALL (866)-434-6067

05. 19. 17

Table of Contents

Summary of Contents for Pulse Performance Products ATV QUAD

Page 1 ELECTRIC QUAD OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ • ATV QUAD DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067 05. 19. 17...
Page 2: Table Of Contents
Pulse Performance Products™ advises that you periodically review and reinforce all information in this manual with all riders, and that you inspect and maintain your motorbike to insure their safety.
Page 3: Safety And Warnings
Safety and Warnings To reduce the risk of injury, adult supervision is required. Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools, or other bodies of water. Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the quad.
Page 4: Before You Start
Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the quad. NOTE: the ATV Quad is to be assembled by an adult. Estimated Assembly Time • Allow up to 15 minutes for assembly, not including initial charge time.
Page 5: Assembly
Assembly Handlebar Assembly Tools required: 5mm hex wrench, 10mm wrench 1. Align handlebars vertically and horizontally 2. Tighten bolts evenly and securely with a 3. Check to ensure handlebars are tight by onto clamps (A&B). Install the 4 clamp bolts 5mm hex wrench (E) and 10mm wrench (F).
Page 6 Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric quad. Required components: battery charger • Initial battery charge time - 14 hours • Recharges after initial charge - up to 10 hours • When quad is not in regular use batteries need to be charged on a monthly basis to maximize performance 1.
Page 7: Hardware Maintenance
Hardware Maintenance Brake Check the brakes for proper function. When you squeeze the lever, the brake should provide positive braking action. When you apply the brake with the throttle engaged, the brake cut off switch should stop the motor. Make sure that the brakes are not rubbing when the lever is not being applied. Frame, Fork and Handlebars Check for cracks or broken connections.
Page 8: Repair And Maintenance
Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Adjusting the Brakes Tools required: 10mm wrench Loosen Tighten 1. To adjust the brake cable, turn the 2. If the brake cable is still either too tight or 3.
Page 9: Repair And Maintenance
Repair and Maintenance WARNING: Turn the power switch “OFF” before conducting any maintenance procedures. Replacing the Chain Tools required: 5mm hex wrench, 6mm hex wrench, 10mm wrench, Philips head screwdriver 1. Remove the rear right side axle bolt 2. Remove the thru axle bolt on the inside of 3.
Page 10 Repair and Maintenance WARNING: RISK OF FIRE. Do not bypass the blade fuse. Replace only with manufacturer replacement parts. Battery Care and Disposal Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C). THIS MOTORBIKE CONTAINS SEALED LEAD ACID BATTERIES WHICH MUST BE RECYCLED IN ACCORDANCE TO YOUR LOCAL AND STATE LAWS.
Page 11 Repair and Maintenance Battery Charger Only use the supplied battery charge r. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ electric quad recommended battery charger. Only use the battery(ies) specified by the manufacturer. Wheels Wheels and drive system components are subject to normal wear and tear.
Page 12: Troubleshooting
Troubleshooting Problem Possible Cause Solution Quad will not run. Battery is not charged. Fully charge the battery. First charge should be 14 hours and up to 10 hours for recharges. Wires or connectors are Check to ensure that charger is tightly plugged into both the wall loose or unplugged.
Page 13 Electric Quad Components part description part description part description Throttle assembly Chain Controller Handlebar Gear Guide wheel Handlebar clamp Gear drive mount Tensioner mount Brake lever Chain guard cover (inner) Motor Left grip Battery lock Left side cover Seat Batteries Left foot rest Body Right fender bracket...
Page 14: Warranty
The manufacturer is not liable for incidental or consequential loss or damage due directly or indirectly to the use of this product. Pulse Performance Products™ does not offer an extended warranty. If you have purchased an extended warranty, it must be honored by the store at which the quad was purchased from.