Advertisement
Quick Links
BlueDAQ QUICK START GUIDE
Software for use with models
BSC4D, BSC8D, BX8 and 9330
BlueDAQ
Software
Issue: 15-258 Revision A
Quick Start Guide
www.interfaceforce.com
Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555
www.interfaceforce.com
● Email:
contact@interfaceforce.com
● ORDER TOLL-FREE 800.947.5598
Advertisement
Related Manuals for Interface BlueDAQ BSC4D
Summary of Contents for Interface BlueDAQ BSC4D
- Page 1 Software for use with models BSC4D, BSC8D, BX8 and 9330 BlueDAQ Software Issue: 15-258 Revision A Quick Start Guide www.interfaceforce.com Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598...
- Page 2 BSC8D/BX8 must be powered ON using supplied power cable and power switch. 9330 drivers must be installed as described below. Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
-
Page 3: Driver Installation
“Include this location in the search:” and then click “Browse”. Select the folder: 9330_Com_Driver from the supplied USB drive. Click “Continue >”. Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598... - Page 4 USB Serial Port (COMX) where X is the assigned port number. Remember this number. In the examples below it is COM6 or COM28 BSC4 9330 Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
- Page 5 BSC8D installs as a Data Acquisition Device Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598...
- Page 6 9330, you will not be allowed to change the number of channels. If using the BSC8/BX8 with a 6-axis sensor then stop after opening 6 channels and proceed to step 11. c. click connect Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
- Page 7 Electrical full scale output is the output of the sensor at the Physical full scale. Input Range is always 2 mV/V and should not be changed. Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ●...
- Page 8 8. Example scaling using Load Cell / BSC8 Digital Bridge Amplifier Calibration Certificate” Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598...
- Page 9 Press Calculate to scale and then OK/Set to save Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598...
- Page 10 “Calculate” and then “OK/Set”. 10. Once each channel has been scaled the software is ready to take measurements. You can now skip to step 17 Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
- Page 11 11. For Six-Axis sensors only. Click “Special Sensor” 12. Select sensor type “Multidimensional sensor” and click OK Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com ● ORDER TOLL-FREE 800.947.5598...
- Page 12 14. Select Change Dir.. and select the folder containing the calibration matrix. This folder is located on the USB flash drive and will be labeled with the transducer serial number. Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
- Page 13 18. When “Load Session” is clicked the settings from the last Session are used. You can also Save and Load Settings Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...
- Page 14 Unpack the zip to a temporary directory, then follow the steps described in the following document, again starting from page 6: http://www.ftdichip.com/Support/Documents/InstallGuides/AN_396%20FT DI%20Drivers%20Installation%20Guide%20for%20Windows%2010.pdf Interface Inc. ● 7401 East Butherus Drive, Scottsdale, Arizona 85260 USA ● Phone 480.948.5555 www.interfaceforce.com ● Email: contact@interfaceforce.com...