Sennheiser AMBEO Instruction Manual

Hide thumbs Also See for AMBEO:

Quick manual (9 pages)

Quick manual (24 pages)

Instruction manual (61 pages)

Table Of Contents

Table of Contents

Quick Links

Summary of Contents for Sennheiser AMBEO

Page 1 Use the search function, the navigation (left) or the following links: Start “Product overview” “Getting started” “Installing the AMBEO Soundbar” “Connecting devices to the AMBEO Soundbar” “Putting the AMBEO Soundbar into operation” “Using the AMBEO Soundbar” “Using the AMBEO Soundbar” “Maintaining the AMBEO Soundbar”...
Page 2: Important Safety Instructions
16. To completely disconnect this product from the AC mains, dis- connect the power supply cord plug from the AC receptacle. 17. The plug of the power supply cord shall remain readily accessible. 2 | AMBEO Soundbar...
Page 3 Keep away from children. Observe correct polarity. Immediately remove the batteries from obviously defective product. Dispose of batteries at special collection points or return them to your specialist dealer. Do not mutilate or dismantle. Do not expose to moisture. AMBEO Soundbar | 3...
Page 4 It is considered improper use when this product is used for any appli- cation not named in the instruction manual. Sennheiser is not liable for damages to USB devices that are not consistent with the USB specifications. Sennheiser does not accept liability for damage aris- ing from improper use or misuse of this product and its attach- ments/accessories.
Page 5 Bluetooth addresses of paired devices, WiFi settings and usage data (e.g. power-on cycles and operating times). This data is required for the operation of the product and is not transferred to Sennheiser or companies commissioned by Sennheiser and is not processed.
Page 6: Package Contents
SB01-WM wall mount for the AMBEO Soundbar, bracket for wall mounting (article no.: 508612) You can find a list of accessories on the AMBEO Soundbar product page at www.sennheiser.com or contact your local Sennheiser partner: www.sennheiser.com > “Service & Sup- port”.
Page 7: Product Overview
Volume button (volume down) Volume +button (volume up) AMBEO button for activating the AMBEO Soundbar  (pressing for 4 seconds activates the room calibration) Multi-function button • for controlling the media playback Bluetooth pairing (by simultaneously pressing the multi-function button and...
Page 8 Output for connecting a subwoofer with power amplifier RCA socket SW PRE OUT RCA input sockets for an analog audio source AUX IN Mounting thread (under the rubber foot) for the SB01-WM wall mount (optional accessory) Type plate 8 | AMBEO Soundbar...
Page 9: Sb01-Rc Remote Control
SPORTS NEUTRAL NIGHT Infrared transmitting diode On/off button AMBEO button for activating the AMBEO Soundbar  (pressing for 4 seconds activates the room calibration) Multi-function button Volume buttons Sound profile button Night mode button Battery compartment (for 1x CR2032 battery)
Page 10: Sb01-Ms Microphone For Room Calibration
Update is being loaded and installed yellow WiFi lost (check router settings, restart flashes router if necessary) Reset is terminated WPS found orange Reset in progress yellow WPS search lights up Soundbar in standby mode 10 | AMBEO Soundbar...
Page 11 Product overview AMBEO display AMBEO display Meaning lights up white AMBEO mode is on AMBEO mode is off pulses white Room calibration in progress The brightness of the AMBEO display and the OLED display can be adjusted via the Smart Control app.
Page 12: Getting Started
Getting started Getting started 1. Setting up the Soundbar The correct placement and setup of the AMBEO Soundbar is import- ant for an optimum sound experience. You can place the AMBEO Soundbar on a piece of furniture (> 15) or mount it directly to a wall using the wall mount (optional accessory) (>...
Page 13 Getting started 3. Connecting the AMBEO Soundbar to the power supply system Connect the AMBEO Soundbar to the power supply system - the AMBEO Soundbar comes to life and guides you through the initial switch-on process (> 27). 4. Starting the room calibration For an optimum spatial sound experience, the AMBEO Soundbar must perform a room calibration.
Page 14 6. Installing the Smart Control app on your smartphone The Sennheiser Smart Control app allows you to use all functions and settings of the AMBEO Soundbar and to e.g. adjust the sound to your liking using the equalizer (> 38).
Page 15: Installing The Ambeo Soundbar
Installing the AMBEO Soundbar Installing the AMBEO Soundbar Placing the Soundbar on the device feet CAUTION Material damage due to overheating Inadequate ventilation may cause the Soundbar to overheat. ▷ Do not place any objects on the Soundbar, keep the minimum clearances and ensure circulating ventilation.
Page 16 Installing the AMBEO Soundbar • The distance of the Soundbar to the TV should be at least 10 cm. • The seat (optimal point “sweet spot”) should be positioned cen- trally in front of the Soundbar and have a distance of at least 2 meters to the Soundbar.
Page 17 Installing the AMBEO Soundbar Optimum positioning Schematic structure of the sound waves from the Soundbar, which are reflected by walls and objects and thus reach the optimal point (“sweet spot”). Thus, a virtual surround sound can be created with a Soundbar.
Page 18: Mounting The Soundbar To A Wall
Installing the AMBEO Soundbar When positioning the Soundbar, keep in mind that the sound is reflected by the walls and ceiling. Many curtains, thick carpets and other rough surfaces can affect the 3D spatial sound. Mounting the Soundbar to a wall...
Page 19: Connecting Devices To The Ambeo Soundbar
“Downmix/Stereo” to “Auto/Bypass/Pass- Through”. (The menu of the devices may use different names depending on the manufacturer). This ensures that the audio signals for 3D spatial sound from the source (e.g. TV) are passed on to the AMBEO Soundbar. Downmix/Stereo Auto/Bypass/Pass-Through ▷...
Page 20 Connecting devices to the AMBEO Soundbar Connecting a TV Connection to the HDMI eARC socket (recommended) ® • Required cable: High Speed HDMI Cable (supplied) To connect the Soundbar to a TV with an HDMI IN socket labeled “ARC/eARC”: ▷...
Page 21 Connecting devices to the AMBEO Soundbar Connection without HDMI eARC socket • Required cable: optical cable (recommended length: max. 5 m) To connect the Soundbar to a TV without an HDMI IN socket labeled “ARC/eARC”: ▷ Connect one connector of an optical cable (to be ordered sepa-...
Page 22: Connecting An Audio/Video Device
Connecting devices to the AMBEO Soundbar Connecting an audio/video device Digital connection • Required cable: HDMI To connect the Soundbar to an audio source (e.g. Blu Ray player, DVD player): ▷ Connect one connector of an HDMI cable (to be ordered sepa-...
Page 23: Connection Diagram (Example)
CD player Audio signal Connection diagram (example) Connect your audio sources to the AMBEO Soundbar and your TV according to the following diagram (example). Sennheiser recom- mends connecting the audio sources for high-resolution surround ® formats directly to the AMBEO Soundbar using a High Speed HDMI Cable.
Page 24: Connecting A Subwoofer (Optional)
Connecting devices to the AMBEO Soundbar Connecting a subwoofer (optional) Optionally, you can connect a subwoofer to the Soundbar. ▷ Recommended settings: Adjust the volume on the subwoofer to “approx. 50%” and set the crossover to “Max”. ▷ Connect one connector of the mono RCA cable (to be ordered...
Page 25: Connecting An Ethernet Cable
Connecting devices to the AMBEO Soundbar Connecting an Ethernet cable To connect the Soundbar to a wired network: ▷ Connect one connector of a network cable (with RJ-45 connector, to be ordered separately) to the ETHERNET socket on the Sound- bar.
Page 26: Using The Usb Socket For Updates
Connecting devices to the AMBEO Soundbar Using the USB socket for updates If the Soundbar is not connected to the Internet, you can install a firmware update on the Soundbar using a USB flash drive. For more information on the update >...
Page 27: Putting The Ambeo Soundbar Into Operation
Putting the AMBEO Soundbar into operation Putting the AMBEO Soundbar into operation Preparing the SB01-RC remote control To remove the transport protection of the battery: ▷ Use a suitable object (e.g. a coin) to open the battery compart- ment cover (located on the bottom side of the remote control) by turning one turn counter-clockwise.
Page 28 Putting the AMBEO Soundbar into operation Disconnecting the Soundbar from the power supply system ▷ Unplug the power plug of the power cable from the wall socket. ▷ Unplug the plug of the power cable from the POWER socket on the Soundbar.
Page 29 AMBEO button on the top of the Soundbar or the AMBEO button on the remote control. display shows “Welcome”. The AMBEO demo sound is played (approx. 10 seconds). ▷ Disconnect the jack plug of the microphone cable from the micro- phone input on the Soundbar.
Page 30 Putting the AMBEO Soundbar into operation Press AMBEO Press AMBEO Please step t Please step to the side Press AMBEO to start callibration Press AMBEO to ﬁnalize Calibration s Press AMBEO Calibration starts in 10 / 9 / .. Press...
Page 31 Putting the AMBEO Soundbar into operation Repeating the calibration If you want to repeat the calibration, you have the following options: • Press the AMBEO button on the Soundbar for 4 seconds. • Press the AMBEO button on the remote control for 4 seconds.
Page 32: Using The Ambeo Soundbar
Using the AMBEO Soundbar Using the AMBEO Soundbar Switching the AMBEO Soundbar on WARNING Danger of hearing damage due to high volume levels! Listening at high volume levels can lead to permanent hearing defects. ▷ Adjust the volume to a low level before selecting a source.
Page 33: Auto Standby
Using the AMBEO Soundbar Auto standby If there is no playback for 20 minutes, the Soundbar automatically switches to standby. No playback: • Bluetooth or Chromecast input is paused • Bluetooth or Chromecast connection is disconnected • Analog, optical or HDMI input: no playback available When playback is muted (“MUTE”), auto standby is not active.
Page 34: Adjusting The Volume
Using the AMBEO Soundbar • Bluetooth • Streaming: – Casting Spotify – Casting TuneIn – Casting Soundcloud • Media The sources Streaming (e.g. Chromecast) and Media can not be selected via the input source buttons. The Soundbar automatically switches to the source when playback is started from the corre- sponding app.
Page 35: Activating/Deactivating The Mute Function
Using the AMBEO Soundbar Activating/deactivating the mute function If you want to activate the mute function, you have the following options: • Press the MUTE button on the Soundbar. • Press the MUTE button on the remote control. • Press the mute button on the TV remote control (if the TV is con- nected to the Soundbar via HMDI CEC).
Page 36: Connecting The Ambeo Soundbar To A Bluetooth/Nfc Device
You can use the Near Field Communication (NFC) function for easy pairing of the devices. paired + connected paired Pairing the AMBEO Soundbar with a Bluetooth device ▷ Activate Bluetooth on your Bluetooth device. ▷ Press the multi-function button...
Page 37 Using the AMBEO Soundbar ▷ From the list of found Bluetooth devices, select “AMBEO Sound- bar”. If necessary, enter the default pin code “0000”. If pairing was successful, the status LED lights up blue. If no connection is established within 3 minutes, pairing mode is terminated.
Page 38: Installing The Smart Control App
To control the Soundbar using a smartphone, Bluetooth Low Energy (Bluetooth LE, at least version 4.2) is required. To make full use of all the settings and functions of the AMBEO Soundbar, you need to have the free Sennheiser Smart Control app installed on your smartphone.
Page 39: Network Connection Via Wifi Or Ethernet
Using the AMBEO Soundbar Hold Network connection via WiFi or Ethernet Use the WiFi connection or the Ethernet connection for: • Chromecast • UPnP (Universal Plug and Play) • Updates Using Chromecast To use Chromecast: ▷ Download the Google Home app.
Page 40: Controlling The Music Playback
Using the AMBEO Soundbar ▷ The Ethernet connection can be set up via the Google Home app and managed via the Smart Control app. If you connect the Soundbar to the Internet/Ethernet via cable, the WiFi function of the Soundbar is automatically deactivated.
Page 41: Adjusting The Ambeo Modes
Using the AMBEO Soundbar Adjusting the AMBEO modes If you want to activate an AMBEO mode, you have the following options: • Press the AMBEO button on the Soundbar. • Press the AMBEO button on the remote control. • Use the Smart Control app.
Page 42: Using The Dolby Drc
Using the AMBEO Soundbar Parameters: • 4-band EQ split into – Foundation – Low-Mid – Clarity – Brillance • Adjustment range + 10 dB to -10 dB The app allows you to make additional acoustical settings in addition to the equalizer settings.
Page 43: Sound Feedback
Using the AMBEO Soundbar If the “Dolby Virtualizer” is activated, you can no longer use the fol- lowing functions/settings: • Sound profiles • AMBEO modes • Equalizer • Room calibration data (the measured room data is not used for Dolby audio content)
Page 44 Using the AMBEO Soundbar To transport the Soundbar: ▷ Switch the Soundbar off (> 32). ▷ Disconnect the Soundbar from the power supply system (> 27). ▷ Disconnect all other cables and connections from the Soundbar (> 19). ▷ With the help of a second person, place the Soundbar, the acces- sories and the foam parts in the original packaging as shown.
Page 45: Maintaining The Ambeo Soundbar
Maintaining the AMBEO Soundbar Maintaining the AMBEO Soundbar Cleaning the Soundbar ATTENTION Liquids can damage the electronics of the product! Liquids entering the housing of the product can cause a short-circuit and damage the electronics. ▷ Keep all liquids far away from the product.
Page 46: Installing Firmware Updates
Required USB flash drive: • Memory size: 1 GB • File system: FAT ▷ Download the update file with the file name “image.swu” from the website www.sennheiser.com/download and save it on a USB flash drive. ▷ Do not change the file name! ▷...
Page 47 Maintaining the AMBEO Soundbar ▷ Press the SETUP button for 5 seconds. The display shows “Updating” and the status LED pulses yellow. Hold The Soundbar restarts several times during the update. The process can take up to 8 minutes. AMBEO Soundbar | 47...
Page 48: Resetting The Soundbar
Maintaining the AMBEO Soundbar Resetting the Soundbar ▷ Switch the Soundbar on. If you want to reset the Soundbar, you have the following options: • Insert a paper clip into the RESET recess on the bottom side of the Soundbar and press the paper clip for 2 seconds.
Page 49: Specifications
Audio processors Dual Core 1.2 GHz ARM Cortex-A7 processor 2 x Dual Core 500 MHz SHARC DSP Display graphic OLED with brightness sensor, status LED, AMBEO LED Power plug county-specific Voltage range 100 – 240 V~ 50/60 Hz Power consumption...
Page 50 2,400 MHz to 2,483.5 MHz (country-specific) 5,170 MHz to 5,835 MHz Modulation 2.4 GHz band CCK, DQPSK, DBPSK für DSSS 64QAM, 16QAM, QPSK, BPSK for OFDM Modulation 5 GHz band 64QAM, 16QAM, QPSK, BPSK Output power 100 mW (max) 50 | AMBEO Soundbar...
Page 51 Near Field Communication (NFC) Network streaming Network Ethernet WiFi Services Chromecast built-in uPnP Playable audio formats Audio format/codec File extension .mp3 AAC/HE-AAC .m4a .aac .mp4 .3gp LPCM .wav FLAC .flac AIFF .aiff .aif ALAC .m4a Vorbis .ogg AMBEO Soundbar | 51...
Page 52 DTS-HD LBR – – DTS:X – – MPEG-H (Fraunhofer) – * not all streaming services support the playback of all codecs ** TV sets with an “ARC” output can transmit surround formats only to a limited extent 52 | AMBEO Soundbar...
Page 53: Manufacturer Declarations
Manufacturer Declarations Manufacturer Declarations Warranty Sennheiser electronic GmbH & Co. KG gives a warranty of 24 months on this product. For the current warranty conditions, please visit our website at www.sennheiser.com or contact your Sennheiser partner. In compliance with the following requirements EU declaration of conformity •...
Page 54 Germany and other countries. This system incorporates High-Definition Multimedia Interface (HDMI™) technology. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo, are trademarks or registered trademarks of HDMI Licensing, LLC in the USA and other countries. 54 | AMBEO Soundbar...
Page 55: Open Source License Terms And Conditions
Open Source license terms and conditions The AMBEO Soundbar SB01 has a user interface to call up additional license terms and conditions for the open source software used. You can open the license terms and conditions on your computer or a mobile device in an Internet browser.

Sennheiser AMBEO Instruction Manual

Quick Links

Related Manuals for Sennheiser AMBEO

Summary of Contents for Sennheiser AMBEO

Table of Contents