TABLE OF CONTENTS Congratulations on purchasing your beamUP garage door opener. It will provide you with many years of Carton Contents Enabling/Disabling Motion Sensing ..........
BEFORE YOU BEGIN SAFETY INSTRUCTIONS WARNING Measure door height. Check mounting Check your toolbox. Do To reduce the risk of severe injury or death: locations. you have all the tools Are additional needed? 1. READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS. reinforcement material 7.5 feet needed?
PREPARE GARAGE DOOR FOR INSTALLATION TOOLS NEEDED DO NOT REUSE PARTS AND WIRING FROM AN OLD OPENER!!! Level BEFORE beginning installation: Adjustable Wrench 1. Disable locks and disengage trolley from current opener. Pencil 2. Perform the following door test to ensure your door is balanced and in good Step Ladder Screwdriver...
RAIL ASSEMBLY Look in the box for: Connect rails starting with the rail header segment. To apply additional force tap gently on the end of the rail Rail – Header Segment with a rubber mallet or on padded flooring. Securely connected by applying force Rail- Middle Segment Rail –...
RAIL AND POWER HEAD ASSEMBLY Look in the box for: Use garage door opener carton to assemble rail to power head. Use packing material as protective base for power head. Rail Bracket Opener Carton Align and slide rail into rail Insert clevis pin into rail Insert hitch pin into clevis pin bracket as shown.
TROLLEY AND PULLEY ASSEMBLY Look in the box for: Slide Trolley onto the rail. Make sure the arrow on the trolley points toward the door. Trolley Pulley Insert pulley into the rail slot. Insert clevis pin through rail Insert hitch pin into clevis pin. hole and pulley.
INSTALLING CABLE AND CHAIN Look in the box for: Align end of chain around sprocket and extend chain past chassis. Pull chain with box along the rail towards Chain/Cable Assembly trolley and then remove box. Chassis Master Link Bring cable and chain Insert cable through circular Pull trolley lock lever down hole in trolley.
INSTALLING CABLE AND CHAIN/ATTACHING SPROCKET COVER Look in the box for: Turn chain-to-cable connector on trolley shaft until chain is about 1/4 inch (.64 cm) above the base of rail. Sprocket Cover Front Tighten until... Chain-to-cable connector 1/4 inch (.64 cm) Attach sprocket cover to Fasten rear tab with flange nut Fasten front tab with self-...
MOUNTING HEADER BRACKET Look in the box for: Above door, mark the center line of the door with a pencil, through wall. Open door to the highest point of Header Bracket 2 x Lag Screw travel. 5/16" x 1-1/2" Highest Point of Travel Center Line WARNING...
ATTACHING RAIL AND MOUNTING DOOR BRACKET Look in the box for: Use garage door opener carton to support power Align header rail hole to header bracket hole. Hitch Pin Clevis Pin head. Rail return pulley end should be pointing to 3/8"...
MOUNTING POWER HEAD TO CEILING Need rewritten text Look in the box for: Raise power head and place it on top of step Angle 4 x Lag Screw 4 x Bolt ladder. Position and align power head with Structural Support Iron 5/16"...
ATTACHING DOOR ARMS Look in the box for: Close your garage door and Fasten straight door arm to Attached door arms fasten with Curved Door Arm rved Door A Straight Door Arm Straight Door Arm disengage trolley. Fasten trolley with a 5/16" x 1" clevis two 5/16"...
INSTALLING EMERGENCY RELEASE HANDLE Look in the box for: * VERY IMPORTANT! * Emergency Release Handle rgency Release Han gency Releas Emergency release handle must clear all vehicles. An Emergency release handle set too low may get caught by the vehicle and cause damage to the opener. Measure from the floor to the top of your vehicle and set the emergency release handle above this measurement.
CONNECTING PHOTO EYE SAFETY SYSTEM Look in the box for: Mount photo eyes. Run wire to head. Use insulated staples to secure Photo Eyes 4x Screw #12 x 1-1/4" photo eyes’ wire to wall or ceiling. Be careful not to Photos eyes damage the wires while securing staples.
CONNECTING POWER AND ALIGNING PHOTO EYE SAFETY SYSTEM WARNING * DO NOT OPERATE OPENER AT THIS TIME * To prevent SERIOUS INJURY or DEATH from electrocution or fire: Plug power head into a grounded outlet ONLY. If there For Permanent Wiring ONLY is no grounded outlet present, call a qualified electrician •...
CONNECTING DELUXE DOOR CONTROL (BU400, BU800) Look in the box for: 1. Strip 7/16 inch (11 mm) of insulation from wire and separate wires. Wire deluxe door control to power Deluxe Door Control* 2x Screw #6 x 1-3/8" head as shown. 2.
MOTION ACTIVATED SECURITY LIGHTING (BU400, BU800) Need images Security lighting is activated Motion sensing is turned on To deactivate motion sensing: and remains on for 4.5 by default and will activate Press and hold “LIGHT” button minutes when garage door security lighting when motion for 2 seconds.
CONNECTING STANDARD DOOR CONTROL (BU100) Look in the box for: 1. Strip 7/16 inch (11 mm) of insulation from wire and separate wires. Wire standard door control to Standard Door Control* 2x Screw #6 x 1-3/8" 2x Screw 6 x 1 3/8 opener as shown.
TRAVEL LIMIT ADJUSTMENT - UP LIMIT Need text from up down limit 110518 PDF WARNING Press and Release LIMIT button once, green light (UP) will turn on. With green light on, press and hold UP To prevent SERIOUS INJURY or DEATH from button, the door will go UP to the desired UP limit position.
TRAVEL LIMIT ADJUSTMENT - DOWN LIMIT Need text from up down limit 110518 PDF WARNING Press and Release LIMIT button TWICE, red light (DOWN) will turn on. With red light on, press and hold DOWN To prevent SERIOUS INJURY or DEATH from button, the door will travel down, to the desired DOWN limit position improper Force Adjustment: •...
SETTING THE FORCE Need text from up down limit 110518 PDF WARNING With both UP and DOWN lights on, press and release the To prevent SERIOUS INJURY or DEATH from FORCE button once to enter Auto Force Setting. improper Force Adjustment: •...
FINAL ADJUSTMENTS AND TESTING WARNING Open door using Place a 1-1/2 inch (3.8cm) Use Door Control to close door. Door MUST To prevent SERIOUS INJURY or DEATH from a door control. flat solid object on the floor, REVERSE and beep within 1.5 seconds upon closing garage door: centered under the garage door.