Related Manuals for Chambers MVW206SS
Summary of Contents for Chambers MVW206SS
-
Page 1: Before Installation
INSTALLATION AND USER MANUAL Model: MVW206SS * Important: Read the complete manual carefully before installation* For accuracy, measurements and rough openings should be done based on the actual hood. -
Page 2: Table Of Contents
CONTENTS INTRODUCTION...............3 SAFETY INFORMATION............3 TOOLS & PARTS...............5 INSTALLATION.................6 OPERATION................12 MAINTENANCE................13 TROUBLESHOOTING..............14 ENVIRONMENTAL PROTECTION..........15 WARRANTY................16 CONTACT INFO.................17... -
Page 3: Introduction
INTRODUCTION Thank you for choosing this cooker hood. This instruction manual is designed to provide you with all required instructions related to the installation, use, maintenance, and warranty of the appliance. Please read this instruction manual carefully before installation and operating your range hood. - Page 4 7. Ducted fans must always be vented to the outdoors. 8. To reduce the risk of fire, use only metal ductwork. 9. This unit must be grounded. TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE: 1. Never leave surface units unattended at high settings. Boil overs cause smoking and greasy spillovers that may ignite.
-
Page 5: Tools & Parts
2. TOOLS AND PARTS REQUIREMENTS Electrical drill or ratchet driver Installation parts Part Photo 1/2” drill bit for drilling pilot holes Bracket for 1pcs 1 ¼” drill bit for drilling electrical wiring access hole. body Screwdrivers: Philips & Straight blade Bracket for 1pcs Pliers... -
Page 6: Installation
4. This appliance has been designed for use in both ducted and recirculating modes, follow the appropriate installation method. (For recirculation mode a kit is required – not included. Contact Chambers® to determine if a kit is available for your hood.) 5. - Page 7 7. The cooker hood should be placed at a distance of 2-3ft (Fig C.) above the cooking surface for best effect. Check your building code for min and max installation heights. 4. INSTALLATION (EXTERIOR VENTILATION): When the range hood is in operation, the negative pressure in the room must not exceed 4 Pa (4×10 Bar) 1.
- Page 8 Screw (4mm x 30mm) Holes on wall Screw plug Wall bracket 2. Lift the cooker hood and hang it onto the wall bracket hooks. Cooker hood Wall bracket 3. After hanging the hood on the bracket, remove the filters, mark 2 holes inside the hood for safety screws.
- Page 9 4. Fix the one-way-valve to the air outlet of the cooker hood. Then, attach the exhaust pipe to the one-way-valve as shown below. Exhaust pipe Cooker hood 5. CHIMNEY INSTALLATION 1. Place the upper chimney into the lower chimney. 2. Use 2 pcs ST4x8mm screws to attach lower and upper chimney together. Before attaching the bracket to the chimney, decide the location of lower chimney bracket fixing holes for fixing the lower chimney bracket in the later steps.
- Page 10 5. Drill 2 holes to accommodate plate II. Screw and tighten plate II onto the wall with two screws and wall plugs provided. Slide the upper chimney up to the correct height and affix the upper chimney with plate II via 2 x ST4x8mm screws. 6.
- Page 11 6. INSTALLATION (RECIRCULATING) If you do not have exterior access, an exhaust pipe is not required. A recirculating kit can be used to clean the air and trap odors. 1. To install the activated carbon filter, the grease filters should be removed first.
-
Page 12: Operation
7. OPERATION Electronic Control On/Off button Low Speed button It’s used for Ventilation on the kitchen. It is suitable for simmering and cooking which do not make much steam. Medium Speed button Airflow speed is ideally for ventilation in standard cooking operation. High Speed button When high density of smoke or steam produced, press high-speed button for highest effective ventilation. -
Page 13: Maintenance
8. MAINTENANCE Before cleaning, switch the unit off and disconnect the electrical supply. I. Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit. -
Page 14: Troubleshooting
TROUBLESHOOTING Fault Cause Solution The fan blade is jammed. Light on, but fan Turn off unit. Repair by qualified service does not work personnel only. The motor is damaged. Light bulb is burnt out. Replace the bulb. Both light and fan do not work Power cord is loose. -
Page 15: Environmental Protection
10. ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. -
Page 16: Warranty
North America only, to hoods installed for normal, non- commercial use in PRIVATE SINGLE-FAMILY HOUSEHOLDS. Chambers® warrants this product to be free from defects in material or workmanship for a period of THREE YEARS from the date of original purchase. During the warranty period, Chambers®... -
Page 17: Contact Info
• Expenses for travel and transportation if your appliance is in a remote area where service by an authorized Chambers® servicer is not available. The cost of repair or replacement under these exclusions shall be borne by the customer and agreed to before a servicer is dispatched.