Related Manuals for Feig Electronic OBID i-scan ID ISC.ANT1700/740-A
Summary of Contents for Feig Electronic OBID i-scan ID ISC.ANT1700/740-A
- Page 1 INSTALLATION ID ISC.ANT1700/740-A /-B Clear Gate Version : Reader ID ISC.LRM2500-B English final public (B) 2011-09-29 M91201-5e-ID-B.doc...
- Page 2 FEIG ELECTRONIC call explicit attention that devices which are subject of this document are not designed with components and testing methods for a level of reliability suitable for use in or in connection with surgical implants or as critical components in any life support systems whose failure to perform can reasonably be expected to cause significant injury to a human.
-
Page 3: Table Of Contents
Reader Configuration with Multiplexer ..............32 5.2.7 Tuning the Gate Antenna with Multiplexer .............. 35 Testing the Gate Antenna..................36 5.3.1 Checking the Noise Level ..................36 5.3.2 Reading a Serial Number ..................38 FEIG ELECTRONIC GmbH Page 3 of 74 M91201-5e-ID-B.doc... - Page 4 8.3.2.1 Antenna ID ISC.ANT1700/740 ..............69 8.3.2.2 People Counter ID ISC.ANT1700/740-GPC ..........70 8.3.3 USA and Canada (UL) ................... 71 Annex A Terminal assignment “Terminal Board” ..............72 Internal wiring ......................74 FEIG ELECTRONIC GmbH Page 4 of 74 M91201-5e-ID-B.doc...
-
Page 5: Safety Instructions / Warning - Read Before Start-Up
Although this device doesn't exceed the valid limits for electromagnetic fields you should keep a minimum distance of 25 cm between the device and your cardiac pacemaker and not stay in an immediate proximity of the reader’s antennas for any length of time. FEIG ELECTRONIC GmbH Page 5 of 74 M91201-5e-ID-B.doc... -
Page 6: Maintenance
Do not try to open the antenna during operation or outside maintenance periods. Non- professional management can result in damage to the device. If any device not working properly, please contact the appropriate representative. FEIG ELECTRONIC GmbH Page 6 of 74 M91201-5e-ID-B.doc... -
Page 7: Performance Features Of The Id Isc.ant1700/740 Antennas
The antennas can be used for detecting both product and persons. It is suitable for installation indoors or outdoors if weather-protected. FEIG ELECTRONIC GmbH Page 7 of 74 M91201-5e-ID-B.doc... -
Page 8: Performance Features Of The People Counter Id Isc.ant1700/740-Gpc
A change of the counter values will be stored in the EEPROM of the People Counter Board. With the command “0x78 Set People Counter” the values could be set/reset to the needed value. FEIG ELECTRONIC GmbH Page 8 of 74... - Page 9 The three digital output can be used, to enable a signal light at every gate antenna or activate an alarm buzzer in the gate antenna. The Connection between reader and people counter takes place trough the RS485 Interface of the reader. FEIG ELECTRONIC GmbH Page 9 of 74 M91201-5e-ID-B.doc...
- Page 10 So, there are two possibilities to get the actual people counter values. Either the Host poll the People Counter periodically or in the Notification Mode of the reader, the reader send a notification protocol at any change of the counter values. See also System Manual H01011-0e-ID-B.DOC FEIG ELECTRONIC GmbH Page 10 of 74 M91201-5e-ID-B.doc...
-
Page 11: Available Antenna Types
ID ISC.ANT1700/740 incl. Mounting and cabling set. (optional) Gate People Counter ID ISC.ANT.GPC-E Second radar detector with cable for the second direct parallel aisle Extension Radar Detector (optional) Table 1: Available Antenna Types and Accessories FEIG ELECTRONIC GmbH Page 11 of 74 M91201-5e-ID-B.doc... - Page 12 GPC-E 740-GPC 2 Antennas 3 Antennas 4 Antennas 5 Antennas 8 Chanel Multiplexer 6 Antennas 8 Chanel Multiplexer 7 Antennas 8 Chanel Multiplexer Table 2 Needed components for gates with People Counter FEIG ELECTRONIC GmbH Page 12 of 74 M91201-5e-ID-B.doc...
-
Page 13: Installation And Wiring
20 cm to all larger metal parts! At a distance of less than 50 cm between the antenna and metal parts the read range will be significantly reduced. FEIG ELECTRONIC GmbH Page 13 of 74... -
Page 14: Mounting Preparation
2. After that the antenna has to be placed carefully again on the floor. Now you must remove the two fastening screws (hexagon socket width A/F2,5) of the antenna cover at the antenna foot and remove it upwards. Fig. 4 Step 1 Step 2 Fig. 4: Opening the antenna base FEIG ELECTRONIC GmbH Page 14 of 74 M91201-5e-ID-B.doc... -
Page 15: Dimensions Of Antenna
4.2 Dimensions of antenna The outside dimensions of the antenna are shown in Fig. 5 Fig. 5: Antenna outside dimensions All dimensions are in mm with general tolerance to ISO 2768 m (mean). FEIG ELECTRONIC GmbH Page 15 of 74 M91201-5e-ID-B.doc... -
Page 16: Drilling The Mounting Holes
Two cable openings are provided for the necessary connection cable (see Fig. 6). The cable openings are dimensioned such that up to 10 cables having a diameter of 6 mm can be passed through each opening. FEIG ELECTRONIC GmbH Page 16 of 74 M91201-5e-ID-B.doc... - Page 17 Reader side. Alternatively the cables can be routed at the sides of the antenna bas like shown in Fig. 7 Fig. 7 Cable routing at the antenna sides FEIG ELECTRONIC GmbH Page 17 of 74 M91201-5e-ID-B.doc...
-
Page 18: Installing The Antenna Base And Antenna Body
5.2 Project Notes People Counter (GPC). Use the adjusting screws (Fig. 9) to align the antenna vertically. Fig. 8 Transverse conductors facing same direction Adjusting screws (hexagon socket width A/F4) Fig. 9: Attaching and aligning the antenna FEIG ELECTRONIC GmbH Page 18 of 74 M91201-5e-ID-B.doc... -
Page 19: Typical Antenna Configuration (Gate Antenna With Two Antennas)
Note that the entire capture area of the antenna is larger than the three-dimensional area shown in the drawing (Fig. 11) . This means there are tag orientations in which the tag can be detected outside the capture area. FEIG ELECTRONIC GmbH Page 19 of 74 M91201-5e-ID-B.doc... - Page 20 The antenna should be at least 50 cm from metal parts. The minimum distance between the antennas of a gate and antennas of RFID work station or terminals (transmitting frequency 13,56 MHz) should be: FEIG ELECTRONIC GmbH Page 20 of 74 M91201-5e-ID-B.doc...
- Page 21 Electrical cable, directly at the antenna or in the immediate vicinity of the antenna, can be cause interference. A minimum distance of 20 cm is required. A minimum distance of 65cm between the two gate antennas is required. FEIG ELECTRONIC GmbH Page 21 of 74 M91201-5e-ID-B.doc...
-
Page 22: Project Notes People Counter (Gpc)
/ masonry . Antenna wall / masonry Type -A Fig. 12: Top: Detection area A1 und A2 (Foot print) of the radar sensor FEIG ELECTRONIC GmbH Page 22 of 74 M91201-5e-ID-B.doc... - Page 23 If greater deviations are found, at first, the sensitivity of the radar sensors should be reduced stepwise. FEIG ELECTRONIC GmbH Page 23 of 74 M91201-5e-ID-B.doc...
-
Page 24: Gate Configuration And Setup Using Antennas Type -A And -B
DATuningTool Version 1.10 or higher ® ® on a personal computer running under Microsoft Windows . The Service Software can be downloaded at the Download Area of the Homepage www.feig.de. FEIG ELECTRONIC GmbH Page 24 of 74 M91201-5e-ID-B.doc... -
Page 25: Configuration Of A Gate Antenna With Multiplexer
Fig. 13: Connecting the components for a gate consisting of two antennas, reader and multiplexer Fig. 14: Terminal board An overview of the terminal board connections you will find in 9. Annex A FEIG ELECTRONIC GmbH Page 25 of 74 M91201-5e-ID-B.doc... - Page 26 A should preferably be connected shortly. Unused cable lengths are possible should be tied in antenna B type. Fig. 15:Connection of the components in an antenna Type A Fig. 16:Tie together the cables in an antenna Type B FEIG ELECTRONIC GmbH Page 26 of 74 M91201-5e-ID-B.doc...
-
Page 27: Setting The Multiplexer
ID ISC.ANT1700/740-A /-B 5.3.3 Setting the Multiplexer Set the jumpers JP11-JP14 shown. More on setting the ID ISC.ANT.MUX.M4 Multiplexer can be found in the corresponding installation manual (M90200-xde-ID-B). Fig. 17: Jumper positions FEIG ELECTRONIC GmbH Page 27 of 74 M91201-5e-ID-B.doc... -
Page 28: Setting The Antenna Tuner
Table 7: Jumper settings for Antenna Tuner Function Jumper Position open 1 Q resistor closed 2 Q resistor Antenna switch offen Capacitor C1 JP 11,12 closed JP 13,14 open Capacitor C2 JP 21,22 open JP 23,24,25,26 closed FEIG ELECTRONIC GmbH Page 28 of 74 M91201-5e-ID-B.doc... - Page 29 ® OBID i-scan Installation ID ISC.ANT1700/740-A /-B Verify these settings. More on setting the ID ISC.DAT antenna tuner can be found in the corresponding installation manual (M40401-xde-ID-B). FEIG ELECTRONIC GmbH Page 29 of 74 M91201-5e-ID-B.doc...
-
Page 30: Interface Connections
Fig. 20: Wiring example for connecting the RS232 interface Note: If there is an USB/RS232 converter used on the PC/Notebook side, we recommend to in- crease the „Char Timeout Multiplier“ parameter in the COM-Port settings from „1“ to about „5“. FEIG ELECTRONIC GmbH Page 30 of 74 M91201-5e-ID-B.doc... -
Page 31: Lan / Tcp/Ip
Table 9 Standard factory configuration of the Ethernet connection Note: The Reader TCP/IP interface has a DHCP option. More Information about the interfaces you will find in the manual M01111-xde-ID-B of the reader. FEIG ELECTRONIC GmbH Page 31 of 74 M91201-5e-ID-B.doc... -
Page 32: Reader Configuration With Multiplexer
Wizard“ and click on „Exit“ This has to be done at each start of ISO-Start program otherwise the configuration of the reader will be changed. Select „Options => Program“ FEIG ELECTRONIC GmbH Page 32 of 74 M91201-5e-ID-B.doc... - Page 33 ® OBID i-scan Installation ID ISC.ANT1700/740-A /-B Step Action Note Select „Expert Mode“ and confirm with OK. Select “Logical View” FEIG ELECTRONIC GmbH Page 33 of 74 M91201-5e-ID-B.doc...
- Page 34 7 Configuring the Reader in accordance with national RF regulations Set by clicking on „Apply“. Operating Mode: For antenna tuning the reader must be set to „Host Mode“. Set by clicking on „Apply“. FEIG ELECTRONIC GmbH Page 34 of 74 M91201-5e-ID-B.doc...
-
Page 35: Tuning The Gate Antenna With Multiplexer
After successful tuning both antennas are shown in green. If this does not succeed on the first try, start the process again by clicking on „Start Tuning“ After successful tuning, close the DATuningTool. FEIG ELECTRONIC GmbH Page 35 of 74 M91201-5e-ID-B.doc... -
Page 36: Testing The Gate Antenna
Set by clicking on “Send” Activate “Test and Measurement” Select „Noise Level“ and start by clicking on „Start“ Normal Noise Level values at antenna 1: Average: < 30mV Difference (Max-Min): < 20mV FEIG ELECTRONIC GmbH Page 36 of 74 M91201-5e-ID-B.doc... - Page 37 Are there devices nearby which may emit noise interferences (larger machines or wireless devices)? Are there interferences from the mains? To determine which devices may be disturbing the gate, briefly disconnect them from the mains. FEIG ELECTRONIC GmbH Page 37 of 74 M91201-5e-ID-B.doc...
-
Page 38: Reading A Serial Number
Measurement“ Select „ISO Inventory“ function and activate by clicking on „Start“. The serial number and tag type will be shown in the display. Repeat Step 1 to 5 for every further antenna FEIG ELECTRONIC GmbH Page 38 of 74 M91201-5e-ID-B.doc... -
Page 39: Testing The Performance
The tag should be read within the gate when moving horizontally through the gate in all three read orientations. If one or more „holes“ are detected, check the noise values on the Reader (see 5.4.1 Checking the Noise Level) . FEIG ELECTRONIC GmbH Page 39 of 74 M91201-5e-ID-B.doc... - Page 40 Transponder too insensitive, detuned or defective Reader improperly configured (transmitting power, transponder type, modulation, transponder parameters, etc.). A cable is defective or has a poor contact. Reader, Power Splitter, Multiplexer or antenna defective. FEIG ELECTRONIC GmbH Page 40 of 74 M91201-5e-ID-B.doc...
-
Page 41: Setting The Alarm Indicators (Alarm Sounder And Alarm Led Lights)
Fig. 23 Volume adjusting To supply the Alarm LED lights with 24V DC the following jumper on the LRM2500 has to be set. JP7,8 and 9. Fig. 24 Jumper settings for relay FEIG ELECTRONIC GmbH Page 41 of 74 M91201-5e-ID-B.doc... -
Page 42: Reader Setting For Indicator
Assign Output 2 to antenna to all antennas of the set up „True“ means: Output 2 will be active if the reader read a valid transponder at the cor- responding antenna. Set by clicking on „Apply“. FEIG ELECTRONIC GmbH Page 42 of 74 M91201-5e-ID-B.doc... - Page 43 Set by clicking on „Apply“ Operating Mode Data se- lector (EAS-Alarm) If the alarm should occur by an EAS, you have to configure the reader as follow: Set “EAS” Set by clicking on „Apply“ FEIG ELECTRONIC GmbH Page 43 of 74 M91201-5e-ID-B.doc...
-
Page 44: Programming A Transponder With The Afi Byte
Transponder Select „[0x27] Write AFI“ ADR: 1: addressed Serial Number: Select TransponderUID AFI: Desired AFI Number (not equal to 00) Write AFI byte on to the transponder by click on „Send“ FEIG ELECTRONIC GmbH Page 44 of 74 M91201-5e-ID-B.doc... -
Page 45: Activating The Automatic Mode
The configuration of the Notification or Scan Mode are similar (See System Manual of the reader) To test the function of the Gate in the Buffered Read Mode, the BRM Window of ISOStart or the BRMDemo program can be used. FEIG ELECTRONIC GmbH Page 45 of 74 M91201-5e-ID-B.doc... -
Page 46: Installation Of The Gate People Counter Id Isc.ant1700/740-Gpc
2 piece split rivet 3,0mm 4 piece hexagon spacer sleeve M3x6 4 piece screw M3x6 1 piece 5 pin connection plug for 2. GPC 5 piece cable-clip 1 piece FCC / IC label FEIG ELECTRONIC GmbH Page 46 of 74 M91201-5e-ID-B.doc... - Page 47 J2. Sensitivity: JP1+2 open : Low JP1 closed: Middle JP2 closed: High JP1+2 closed: Very high Recommended Sensitivity: High Install Radar module with split rivet 3,0 mm at the mounting bracket. FEIG ELECTRONIC GmbH Page 47 of 74 M91201-5e-ID-B.doc...
- Page 48 The other plug will be used for the second radar sensor, in case of a gate with two aisle. Install the mounting bracket in the antenna with 4 pieces. split rivet 4,0 mm FEIG ELECTRONIC GmbH Page 48 of 74 M91201-5e-ID-B.doc...
- Page 49 Installation ID ISC.ANT1700/740-A /-B Fix the cable with the cable clips beside the coax cable. Install People Counter Board with the hexagon spacers and the screws into antenna foot beside the multiplexer. FEIG ELECTRONIC GmbH Page 49 of 74 M91201-5e-ID-B.doc...
- Page 50 X1 1. Remove connector form X5 GPC-in and the three wires from X2 of the reader ID ISC.LRM2500. Plug connection cable of People Counter onto X5/GPC-IN of Terminal Board.. FEIG ELECTRONIC GmbH Page 50 of 74 M91201-5e-ID-B.doc...
- Page 51 After the installation you have to stick the adhesive label of the GPC below of the type plate of the antenna FEIG ELECTRONIC GmbH Page 51 of 74 M91201-5e-ID-B.doc...
- Page 52 ID ISC.ANT.GPC-E ID ISC.ANT1700/740-GPC Long Range Reader Gate People Counter ID ISC.LRM2500-B ID ISC.ANT1700/740-GPC LED2 LED3 Second GPC 4. Antenna (Type B) Optional Antenna B ANtenna B Fig. 25: Connections ID ISC.ANT1700/740-GPC FEIG ELECTRONIC GmbH Page 52 of 74 M91201-5e-ID-B.doc...
-
Page 53: Installation Id Isc.ant.gpc-E
Set sensitivity of Radar sensor by setting jumper J1 and J2. Sensitivity: JP1+2 open: Low JP1 closed: Middle JP2 closed: High JP1+2 closed: Very high Recommended Sensitivity: High FEIG ELECTRONIC GmbH Page 53 of 74 M91201-5e-ID-B.doc... - Page 54 3,0mm at the back of the mounting bracket Connect second plug of radar connection cable with X1 of Radar module. Here: red/Grey/blue/pink Plug second plug of Radar connection cable onto X12 Sen 2 FEIG ELECTRONIC GmbH Page 54 of 74 M91201-5e-ID-B.doc...
- Page 55 ® OBID i-scan Installation ID ISC.ANT1700/740-A /-B Radar Module Radar Module ID ISC.ANT.GPC-E ID ISC.ANT1700/740-GPC Gate People Counter ID ISC.ANT1700/740-GPC Fig. 26: Connections GPC-E 2.Radarmodule FEIG ELECTRONIC GmbH Page 55 of 74 M91201-5e-ID-B.doc...
-
Page 56: Configuration And Test
Fig. 28. At one reader, up to 3 People Counter (bus address 1-3) could be operated. Fig. 28: Position of Dip Switch at People Counter Board DIP-Switch S1 bus address OFF/ON Reserved Table 10 Setting the bus address of People Counter FEIG ELECTRONIC GmbH Page 56 of 74 M91201-5e-ID-B.doc... -
Page 57: Connecting Several People Counter
9.Annex A e.g. 1.People Counter 2. People Counter 3. People Counter in Antenna A in Antenna Type B in Antenna Type B (2.Antenna) (4.Antenna) (6. Antenna) Fig. 29 Connecting the People Counters FEIG ELECTRONIC GmbH Page 57 of 74 M91201-5e-ID-B.doc... -
Page 58: Configuration And Test In Iso-Host Or Buffered Read
Output 2 to antenna 2. Output 3 to antenna 3. „True“ means: Output 1,2 or 3 will be active if the reader read a valid trans- ponder on the correspond- ing antenna FEIG ELECTRONIC GmbH Page 58 of 74 M91201-5e-ID-B.doc... - Page 59 Confirm with „Send“ Select Command „Get People Counter Values“ Confirm with „Send“ All counter values should be 0 Walk through the gate from both directions. Counter 1 | Counter 2 | Out FEIG ELECTRONIC GmbH Page 59 of 74 M91201-5e-ID-B.doc...
-
Page 60: Configuration And Test In Notification Mode
The following configuration hast o be done: Step Action Note Select „Configuration“ Peripheral Devices/CFG8 Set People Counter and Notify Counter to „True“ Confirm with „Apply“ Operating Mode Select -Notification Mode Confirm with „Apply“ FEIG ELECTRONIC GmbH Page 60 of 74 M91201-5e-ID-B.doc... - Page 61 : 192.168.3.213 Port:20005 Set IP Address and Port for People Counter IP Address of Host e.g. here: 192.168.3.213 Port:10005 Confirm with „Apply“ A Test could be done with the People Counter Sample. FEIG ELECTRONIC GmbH Page 61 of 74 M91201-5e-ID-B.doc...
-
Page 62: Configuring The Reader In Accordance With National Rf Regulations
When placing the antennas in service, the systems integrator must ensure that the prescribed mounting instructions are followed, the necessary Reader settings are made and permissible limits according to the national regulations are not exceeded. FEIG ELECTRONIC GmbH Page 62 of 74 M91201-5e-ID-B.doc... - Page 63 RF Modulation / ISO-MODE / RF Data coding ISO-MODE: Fast (1/4) or Normal (1/256) Timeslots ISO-MODE / NO-TS 1 or 16 Timeslots ISO Option – BREAK: Complete Timeslot length at „NO TAG“ FEIG ELECTRONIC GmbH Page 63 of 74 M91201-5e-ID-B.doc...
-
Page 64: Technical Data
Permissible overall transmitting power per antenna gate – EU-territory (per EN 300 330) 8.0 W – USA (per. FCC Part 15) 8.0 W 8.0 W - Canada (per RSS 210) FEIG ELECTRONIC GmbH Page 64 of 74 M91201-5e-ID-B.doc... - Page 65 – All tag orientations approx. 104 / 110 cm*** Antenna connection 1 x SMA plug (50 ) Antenna connector cable RG58, 50 , approx. 7,20 m long - Type B FEIG ELECTRONIC GmbH Page 65 of 74 M91201-5e-ID-B.doc...
- Page 66 8 W, aligned in all 3 dimensions for horizontal movement through the antenna. The maximum antenna distance also depending of the strength of the Transponder answer signal! Z.B NXP I-Code SLi / NXP I-Code SLi-S FEIG ELECTRONIC GmbH Page 66 of 74 M91201-5e-ID-B.doc...
-
Page 67: People Counter Id Isc.ant1700/740-Gpc And Id Isc.ant.gpc-E
max. 2 VA Operating Frequency 24,125 GHz RF-Output power 16 dBm (e.i.r.p.) Temperature range – Operation –25 °C bis +55 °C – Storage –25 °C bis +85 °C FEIG ELECTRONIC GmbH Page 67 of 74 M91201-5e-ID-B.doc... -
Page 68: Approval
This RF equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC dated March 99. Equipment Classification according to ETSI EN 300 330 and ETSI EN 301 489: Class 2 FEIG ELECTRONIC GmbH Page 68 of 74 M91201-5e-ID-B.doc... -
Page 69: Usa (Fcc) And Canada (Ic)
Further information and technical data of the ID ISC.LRM2500-B Reader built into the ID ISC.ANT1700/740 antenna can be found in the Installation Manual which is included with the device. FEIG ELECTRONIC GmbH Page 69 of 74 M91201-5e-ID-B.doc... -
Page 70: People Counter Id Isc.ant1700/740-Gpc
: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonc- tionnement. FEIG ELECTRONIC GmbH Page 70 of 74 M91201-5e-ID-B.doc... -
Page 71: Usa And Canada (Ul)
® OBID i-scan Installation ID ISC.ANT1700/740-A /-B 8.3.3 USA and Canada (UL) The following picture indicates the label position: FEIG ELECTRONIC GmbH Page 71 of 74 M91201-5e-ID-B.doc... -
Page 72: Annex A
+24V DC LEDB X14 / Pin 2 GND LEDB 24V DC Power Supply X11 / Pin 1 Power Supply +24 V DC Ground – Power Supply X11 / Pin 2 - / GND FEIG ELECTRONIC GmbH Page 72 of 74 M91201-5e-ID-B.doc... - Page 73 X13 / Pin 5 RS485-B X14 / LED3 Connection LED / Alarm light 3. Antenna X14 / Pin 1 +24V DC LED3 X14 / Pin 2 GND LED3 Table 11: Pin-Configuration X11-X14 Terminal Board FEIG ELECTRONIC GmbH Page 73 of 74 M91201-5e-ID-B.doc...
-
Page 74: Internal Wiring
Reader LR2500 X2 Pin REL2-COM (yellow) X5 / Pin 3 Reader LR2500 X2 Pin REL1-COM (green) X6 / LED 1 X6 / Pin 1 LED X1 + (green) X6 / Pin 2 LED X1 - (yellow) FEIG ELECTRONIC GmbH Page 74 of 74 M91201-5e-ID-B.doc...