Summary of Contents for Datalogic DS2x00N-DS4800 Series
Page 1
DS2X00N-DS4800 SCANNER FAMILY SETUP PROCEDURE USING PROGRAMMING BARCODES 1 ID-NET™ NETWORK SETUP USING PROGRAMMING BARCODES For any DS2x00N-DS4800 Family scanner, programming barcodes can be used to setup the ID-NET™ built-in high-speed interface dedicated for high-speed reader interconnection. ID-NET™ is in addition to the Main and Auxiliary serial interfaces. Following topologies are available: ID-NET™...
Page 2
Setup Procedure Using Programming Barcodes ID-NET™ M/S Multidata: Multiple stations – single scanner Master Slave#1 Slave#n Terminal Power Host Main Serial Interface (RS232 or RS485) Auxiliary Serial Interface (Local Echo) (RS232) External Trigger (for On-Line Mode) ...
Page 3
Setup Procedure Using Programming Barcodes 1. Press and hold the X-PRESS™ button to enter the “AutoLearn Mode”. Once button is pressed, the LED cycle appears as follows: READY READY READY READY GOOD GOOD GOOD GOOD SETUP SETUP SETUP SETUP TRIGGER TRIGGER TRIGGER TRIGGER...
Page 4
Setup Procedure Using Programming Barcodes 4. The scanner is programmed and the AutoLearn Mode ends. The green “ready” LED is on. READY GOOD SETUP TRIGGER LEARN TEST STATUS Programming done. 5. Repeat steps 1..3 above to configure all the slaves and master. The maximum number of scanners is 32, including the master.
Page 5
Setup Procedure Using Programming Barcodes 7. Start the Genius™ Express Network Setup procedure. Refer to the Help On Line document for details. Any network role can also be programmed using Genius™. Refer to the Help On Line documentation for further details. NOTE...
Page 12
Setup Procedure Using Programming Barcodes 2 STAND-ALONE LAYOUT BARCODE In order to re-program a network scanner for a stand alone configuration, the following barcode can be used. Stand Alone Layout Host PG6000 Scanner Terminal Main Serial Interface (RS232 or RS485 Full-Duplex) ...
Page 13
Setup Procedure Using Programming Barcodes 3 X-PRESS™ KEY LOCK – UNLOCK BARCODE The X-PRESS™ key can be locked and unlocked through two different methods: by means of a Genius™ parameter with a programming barcode The programming barcode procedure uses the AutoLearn Mode as described in chapter 1. The code below is a “toggle-code”: if the key is locked, the programming code will unlock the key ...
Page 14
Setup Procedure Using Programming Barcodes 5 NETWORK STATUS MONITOR LOCK – UNLOCK BARCODE For Master scanners with display (or connected to a CBX500 with accessory display), the Network Status Monitor shows diagnostic messages regarding the network. It can be enabled/disabled through two different methods: by means of a Genius™...
Page 15
Setup Procedure Using Programming Barcodes 6 TCP/IP ETHERNET INTERFACE TO HOST For any DS2x00N-DS4800 Family scanner having software package 005 or later, connected to either a QL500 or to a BM2x0 module (inside a CBX connection box), you can setup the Ethernet communication with programming barcodes.
Page 16
Setup Procedure Using Programming Barcodes 2. Launch the Finder program on the Genius™ CD-ROM in .. Doc\Software Utilities\QL500- to determine the IP address assigned to the scanner. BM2x0 IP Finder.zip 3. Set the Genius™ Tools>Options>Communications window to TCP/IP and in the Device address or name field, input the IP address returned by the finder program.
Page 17
Setup Procedure Using Programming Barcodes 5. Set the IP Address fields as follows and click OK to save. 6. Set the Genius™ Tools>Options>Communications window to TCP/IP and in the Device address or name field, input the scanner Factory Default address. The port number is 51235.
Page 18
Setup Procedure Using Programming Barcodes The following figures are examples of these layouts: Power CAB-PW-EXT DS2100N Host QL500 Ethernet Point to Point - DS2100N with QL500 (Ethernet to Host) The Point-to-Point reader must be configured for Ethernet communication using the specific programming barcode.
Page 19
Setup Procedure Using Programming Barcodes Power Slave#1 Slave#n CBX500 Master BM200/210 TCP/IP Ethernet Interface External Trigger Host ID-NET™ (up to 16 devices - practical limit) ID-NET™ M/S Synchronized Layout with BM200/210 TCP/IP Ethernet Interface to Host Power CBX500 Master Slave#1...
Page 20
Setup Procedure Using Programming Barcodes 7 PARAMETER SETTING SUMMARY The network setup through programming barcodes automatically sets all the necessary parameters in order to produce a consistent and correct configuration. The following table summarizes the modified values and the related programming actions. Programmed Code Modified Parameters Topology Role = Other...