Table of Contents
Advertisement
•
11. Summary of all communicator texts for SMS messages and instructions
n
factory default text:
0
Report from your alarm:
1
Wired detector #1
2
Wired detector #2
3
Wired detector #3
4
Wired detector #4
5
Wired detector #5
6
Wired detector #6
7
Wired detector #7
8
Wired detector #8
9
Wired detector #9
10
Wired detector #10
11
Wired detector #11
12
Wired detector #12
13
Wired detector #13
14
Wired detector #14
15
Wired detector #15
16
Wired detector #16
17
Wireless detector #1
18
Wireless detector #2
19
Wireless detector #3
20
Wireless detector #4
21
Wireless detector #5
22
Wireless detector #6
23
Wireless detector #7
24
Wireless detector #8
25
Wireless detector #9
26
Wireless detector #10
27
Wireless detector #11
28
Wireless detector #12
29
Wireless detector #13
30
Wireless detector #14
31
Wireless detector #15
32
Wireless detector #16
33
Controller #1
34
Controller #2
35
Controller #3
36
Controller #4
37
Controller #5
38
Controller #6
39
Controller #7
40
Controller #8
41
Wireless siren
42
Subsystem
201
Control panel
202
Service code
204
Communicator
205
Keypad
206
ARC code
Notes:
− The communicator always automatically puts numbers from 01 to 42 in front of Device names
− Texts 0 to 554 are used to create SMS event reports
− Texts 601 to 611 are SMS instructions (to control the system remotely by SMS)
− Texts are set by ComLink software
− Other texts with diacritics, if required, can be loaded from a file and save to the communicator
The JA-62GSM communicator for GSM
n
factory default text:
300
Master code
301
Code #1
302
Code #2
303
Code #3
304
Code #4
305
Code #5
306
Code #6
307
Code #7
308
Code #8
309
Code #9
310
Code #10
311
Code #11
312
Code #12
313
Code #13
314
Code #14
400
System status
401
Set
402
Unset
403
Exit delay
404
Entrance delay
405
Alarm
406
Service mode
407
Maintenance mode
409
Discharged battery
410
Tamper alarm
411
Alarm memory
412
Fault
413
Power failure
414
Unknown status
415
Time:
416
Last event:
417
Credit unknown
418
Credit
420
Error while processing command
421
Output turned ON
422
Output turned OFF
423
Partially set A
424
Partially set B
426
Command processing OK
501
Instant alarm
502
Delayed alarm
503
Fire
504
Panic alarm
505
Invalid code-entries exceeded
506
Alarm when power turned ON
507
Tamper alarm
508
End of tamper alarm
509
End of alarm indication
tab. 6 table of factory-default SMS report and instruction texts
9 / 11
n
factory default text:
510
Alarm cancelled by user
511
Setting
512
Unsetting
514
Codeless setting
515
External communication failure
516
External communication restored
517
Fault
518
Fault no longer present
519
Mains dropout over 30 minutes
520
Mains dropout
521
Mains recovery
522
Discharged battery
523
System power OK
524
Switching to Service Mode
525
Leaving Service Mode
528
Radio jamming present
529
Internal communication failure
530
Internal communication restored
531
Communication test
535
Partial setting A
536
Partial setting B
538
Partial unsetting A
539
Partial unsetting B
540
Communicator failure
541
Communicator OK
542
Backup battery failure
543
Backup battery OK
545
Credit low
546
Power ON
549
Master code change
550
Message delivered
551
Message not delivered
553
PG ON
554
PG OFF
601
SET
602
UNSET
603
STATUS
604
MEMORY
609
PGON
610
PGOFF
611
CREDIT
MLD52902
Advertisement
Table of Contents
