Table of Contents
Advertisement
Function
ARC main telephone number / IP
address
ARC backup telephone number / IP
address
Installation (alarm system) ID for ARC
use
Selecting the ARC communication
protocol
Selection of events to report to ARCs
Periodic or fixed ARC connection
check
ARC communication checking period
Enable ARC reporting (ARC2 backs
up ARC1)
Recording reports sent to ARCs in the
control panel memory
Indicates an ARC communication fault
if a report is not successfully received
within 110 sec of transmission
Locking the ARC settings
Unlocking the ARC settings
Period of waiting before repeating
unsuccessful communication to the
ARC
Number of repeated attempts after
unsuccessful communication to the
ARC
The JA-62GSM communicator for GSM
Tab. 7 communicator programming sequence continued
Sequence
p=1 ARC1, p=2 ARC2 xx..x = tel. number max.
30 digits. When using IP protocol, IP addresses
01 p xx..x F0
are entered instead of telephone numbers
To erase the corresponding telephone
numbers or IP addresses enter 01pF0
p=1 ARC1, p=2 ARC2, xx..x = tel. number max.
30 digits. When using IP protocol, IP addresses
02 p xx..x F0
are entered instead of telephone numbers
To erase the corresponding telephone
numbers or IP addresses enter 02pF0
p=1 ARC1, p=2 ARC2, xx..x = installation
03 p zz..zF0
number max. 8 characters 0 to 9 and F1=A to
F6=F
p=1 ARC1, p=2 ARC2,
x=0 CID,
04 p x
x=1 Jablotron GPRS,
x=2 Jablotron SMS,
p=1 ARC1, p=2 ARC2
uu is an event code (see 7.4)
05 p uu x
x=0 no report,
x=1 report
p=1 ARC1, p=2 ARC2
x=0 with a period from the last report according
06 p x
to the 07 p hhmm setting
x=1 once a day at the time set by
entering 07 p hhmm
p=1 ARC1, p=2 ARC2
07 p hhmm
hhmm = hours, minutes, see setting via 06 p x
p=1 ARC1, p=2 ARC2
x=0 reports disabled,
08 p x
x=1 reports enabled,
x=2 only for ARC1, sets that ARC2 backs up
ARC1
x=0 no (only records ARC communication
faults)
001 x
x=1 yes (all reports except communication
checks)
x=0 no
002 x
x=1 yes
xx..x is your code (4 to 8 digits)
Entering this code and then exiting service
091 xx..xF0
mode will lock the ARC settings
091 F0 will erase the code (permanently
unlocked)
092 xx..xF0
xx..x is the locking code used by sequence 091
p=1 ARC1, p=2 ARC2
0001 p mmss
mmss = minutes, seconds
p=1 ARC1, p=2 ARC2
0002 p n
n= 1x to 9x
Possible options
11 / 11
Factory default settings
erased
erased
0000
p1 Jablotron GPRS
p2 Jablotron SMS
All events are reported - see tab. 3
With a period after the last report (X=0)
2359
1,2 ARC reporting disabled
no
no
unlocked
ARC programming can be temporarily enabled in
service mode by entering this sequence. It will
then relock on exiting service mode. For
permanent unlocking see sequence 091.
Without delay (0000)
2x
MLD52902
Advertisement
Table of Contents
