Advertisement
TabLe 4. 2-Wire Horn/STrobe CurrenT draW (
DC Input
15 cd
Temporal High
Temporal Medium
Temporal Low
Non-temporal High
Non-temporal Medium
Non-temporal Low
FWR Input
Temporal High
Temporal Medium
Temporal Low
Non-temporal High
Non-temporal Medium
Non-temporal Low
TabLe 5. 2-Wire Horn/STrobe CurrenT draW (
Sound Pattern
Temporal High
Temporal Medium
Temporal Low
Non-temporal High
Non-temporal Medium
Non-temporal Low
TabLe 6. Horn ouTpuT ( ba) in uL reverberanT room:
d
Switch
Sound Pattern
Position
1
Temporal
High
2
Temporal
Medium
3
Temporal
Low
4
Non-temporal
High
5
Non-temporal
Medium
6
Non-temporal
Low
7*
Coded
High
8*
Coded
Medium
9*
Coded
Low
*Horn & 4-wire Horn/Strobe only. ** Minimum dB rating for Operational Voltage Range as per UL 464.
mounTing indoor WaLL or CeiLing produCTS
1.
Attach mounting plate to junction box as shown in Figures 4 and 5. The
mounting plate is compatible with 4-inch square, double gang, and 4-inch
octagon junction boxes (2-wire products may be used with a single gang
box). If using a back box skirt, attach the mounting plate to the skirt and
then attach the entire assembly to the junction box (see Figures 6 and 7).
2.
Connect field wiring to terminals, as shown in Figures 1 and 2.
3.
If the product is not to be installed at this point, use the paint cover to
prevent contamination of the mounting plate. (For indoor models only)
4.
To attach product to mounting plate, remove the paint cover, then hook
tabs on the product housing into the grooves on mounting plate.
5.
Then, swing product into position to engage the pins on the product with
the terminals on the mounting plate. Make sure that the tabs on the back
of the product housing fully engage with the mounting plate.
6.
Secure product by tightening the single mounting screw in the front
of the product housing. For tamper resistance, the standard captivated
mounting screw may be replaced with the enclosed Torx screw.
D690-03-00
ma
) For p2 and pC2 STandard CandeLa SerieS:
8–17.5 Volts
15/75 cd
15 cd
137
147
79
132
144
69
132
143
66
141
152
91
133
145
75
131
144
68
136
155
88
129
152
78
129
151
76
142
161
103
134
155
85
132
154
80
) For p2 and pC2 HigH CandeLa range SerieS:
ma
16–33 Volts Volts DC
135 cd
150 cd
245
259
235
253
232
251
255
270
242
259
238
254
8–17.5 Volts**
dA
DC
FWR
78
78
75
75
71
71
82
82
78
78
75
75
82
82
78
78
74
75
15/75 cd
30 cd
90
107
80
97
77
93
100
116
85
102
79
96
97
112
88
103
86
101
112
126
95
110
90
105
177 cd
185 cd
135 cd
290
297
288
297
282
292
303
309
293
299
291
295
16–33 Volts**
DC
FWR
84
84
80
80
76
76
88
88
85
85
81
81
88
88
85
85
81
81
k SerieS mounTing
1.
K Series products may be used indoors or outdoors. They must be in-
stalled using the proper SpectrAlert Advance weatherproof back box (SA-
WBB, SA-WBBW, SA-WBBC or SA-WBBCW). Do not attempt to use boxes
other than the ones supplied with the product.
2.
The wall mount box (SA-WBB or SA-WBBW) must be mounted with its
internal post in the lower left corner, as shown in Figure 8.
3.
Threaded holes are provided in the sides of the box for ¾-inch conduit
adapters. Knockout plugs in the back of the box can be used for ¾-inch
rear entry. Unused holes must be sealed. Plugs and O-Rings are provided
with the box for this purpose.
4.
It is the responsibility of the installer to make sure that all openings and
connections are sealed properly. Outdoor installations that are protected
from direct exposure to rain are still subject to condensation or leakage
through hidden areas, such as a soffit.
5.
Water may pool on the back box due to condensation or direct exposure
to rain or snow. Use watertight fittings for all wiring connections, includ-
ing the knockout plugs on the back of the box. When using plastic plugs
to fill unused threaded holes, apply teflon tape and/or silicone sealant to
reduce the chance of leakage.
6.
Attach the mounting plate to the weatherproof back box using the four
unpainted screws.
7.
Follow steps 2 – 6 of the indoor mounting instructions to wire and attach
the product.
3
16–33 Volts
75 cd
95 cd
110 cd
176
194
157
182
154
179
176
201
163
187
156
182
168
190
160
184
160
184
181
203
166
189
161
184
16–33 Volts Volts FWR
150 cd
177 cd
215
231
258
209
224
250
207
221
248
233
248
275
219
232
262
214
229
256
24 V Nominal Measurements
Reverberant
DC
FWR
88
88
86
85
81
79
93
92
90
89
86
84
93
92
90
89
85
83
115 cd
212
218
201
210
198
207
221
229
207
216
201
210
210
218
202
206
194
201
221
229
208
216
202
211
185 cd
265
258
256
281
267
262
Anechoic
DC
FWR
99
98
96
96
94
89
100
100
98
98
96
92
101
101
97
98
96
92
I56-2769-015R
Advertisement
