Installing Cables Installing the UPS Output Power Cables For socket-type output, connect loads to the UPS output sockets UPS load UPS2000-G-1KRTS UPS2000-G-1KRTL UPS load UPS load UPS2000-G-2KRTS...
Page 5
UPS2000-G-2KRTL UPS load UPS2000-G-3KRTS UPS2000-G-3KRTL UPS load UPS load Installing the UPS Battery Cable (Only for UPS with Long Backup Time) Connect the battery cable delivered with the long backup time model to an external battery pack. (This step is optional for the long backup time model. The standard model contains batteries and provides no battery port.) The installation method for 1 kVA UPS, 2 kVA UPS, and 3 kVA UPS is the same.
Page 6
NetEco 1000U User Manual. The software and the user manual are available at http://support.huawei.com or http://support.huawei.com/enterprise. Connect the UPS to the RS232 or USB port on a PC. Then you can monitor the UPS status using the PC as long as you have installed the monitoring software. The installation method for 1 kVA UPS, 2 kVA UPS, and 3 kVA UPS is the same.
UPS2000-G-2KRTS UPS2000-G-2KRTL Mains input Mains input UPS2000-G-3KRTS UPS2000-G-3KRTL Mains input Mains input Installing the Optional Card to the UPS For the installation procedure, see the RMS-SNMP01B SNMP Card User Manual, RMS-RELAY01B User Manual, RMS-MODBUS01B User Manual. The installation method for 1 kVA, 2 kVA UPS, and 3 kVA UPS is the same.
Page 8
Operations ON/MUTE SELECT OFF/ENTER Setting Key UPS Parameters 1. The 1 kVA UPS with standard backup time have two built-in batteries, the 2 kVA UPS with standard backup time have four built-in batteries, the 3 kVA UPS with standard backup time have six built-in batteries.
Page 9
1. In the preset mode, LCD will return to the main page with 10 seconds of no operation. 2. If the long backup time model is not connected to an external battery pack, the buzzer keeps buzzing. 3. The UPS performs a battery self-check automatically once a week. If batteries are faulty, an alarm is generated.
Page 10
Character Display Description Acronym Display Description Acronym Display Description Enable Frequency Disable Bypass overvoltage Escape Bypass undervoltage Frequency Capacity conversion Temperature Discharge time Charging ECO mode Bypass frequency High voltage unstable EEPROM error Low voltage Voltage Constant-frequency mode Buzzer off Automatic startup Buzzer Alarm Tone Description Alarm type...
Troubleshooting Symptom Possible Cause Measures The main power is The mains input power cable is Check the input power cable. normal, but no indicator disconnected. turns on and the buzzer The mains input power cable is Correctly connect the mains input generates no tone.
Alarm Handling For more alarm handling, see the UPS2000-G-(1 kVA-3 kVA) User Manual. Alarm Alarm Alarm Trigger Impact on Repair Proposal Name Sever Clear Condition the System Mode Bypass Minor This The UPS Possible causes: voltage alarm is bypass remains in the The bypass input abnorm automatic...
Page 13
Alarm Alarm Alarm Trigger Impact on the Repair Proposal Name Severit Clear Conditi System Mode • Battery Critical This This alarm is Possible cause: overvol alarm voltage generated because The actual tage must of each there are more number of battery batteries than batteries does not...
Page 14
• Possible cause: The battery is damaged. Measure: Contact the dealer or Huawei Minor This The voltage of The UPS remains technical alarm each battery is in the current support to lower than 5...
Page 15
Measure: Check that the load types are supported by the UPS. • Possible cause: The hardware is damaged. Measure: Contact the dealer or Huawei technical support. For more information, refer to the channels provided on the following page.
Page 16
Google Play Huawei App Store Scan here for more documents: Support-E Support WeChat You can also log in to Huawei technical support website: http://support.huawei.com/enterprise http://support.huawei.com HUAWEI TECHNOLOGIES CO., LTD. Huawei Industrial Base, Bantian, Longgang Shenzhen 518129 People's Republic of China...