Viking K-1900-3 Product Manual page 6
Door entry dialer
Hide thumbs
Also See for K-1900-3:
- Technical practice (8 pages) ,
- Buyer's manual (16 pages) ,
- User manual (8 pages)
Table of Contents
Advertisement
E. Programming Features Quick Reference
Programming Features
Tenant's phone numbers: 001-002 (0-32 digits), 003-250 (0-16 digits) phone number
Tenant's phone numbers and keyless entry codes ................................
Keyless entry code only (4 - 6 digits) ...................................................... #Q + entry code
Master keyless entry code (4 - 6 digits) ................................................. #Q + entry code
Maintenance personnel entry codes (4-6 digits) .................................... #Q + entry code
Clear one phone number and/or keyless entry code .............................. (no digits)
PABX line access number: 1-3 digits + 3 sec pause
Relay activation time: .5-99 sec
Relay activation code*: 1-2 digits (factory set to 36) .............................. 1-2 digits (00 - 99)
Security code (factory set to 845464) .................................................... 6 digits (0 - 9)
Maximum call time: 0-99 min (00 = disabled, factory set to 2 min) ........ 2 digits (00 - 99)
To exit remote programming ................................................................... (no digits)
Normal dialing speed (120ms on/off, factory setting) ............................. Q1
Fast dialing speed (50ms on/off) ............................................................ Q2
Apartment dialer mode (factory setting) ................................................. Q3
Multi-number dialer mode ...................................................................... Q4
Ring thru mode OFF (factory setting) .................................................... Q5
Ring thru mode ON ................................................................................ Q6
To add a 4 second pause anywhere in the dialing string ....................... Q7
To add a 1 second pause anywhere in the dialing string ....................... Q8
Enable 911 and 311 calling from entry phone (factory setting) .............. Q9
Disable 911 and 311 calling from entry phone ....................................... Q0
To add a Q at any point in the dialing string ........................................... QQ
To add a # at any point in the dialing string ............................................ Q #
Clear all phone numbers and keyless entry codes from memory
and set all programming features back to factory settings .................... ###
* Note: When a single digit relay activation code is programmed (0-9), the activation Touch Tone must be held for
a minimum of 150 milliseconds.
Notes: "Q", "#", pauses occupy one digit space in memory. To clear a memory location, enter "#" + the memory
location without any preceeding digits. A valid programming entry will be indicated by a double beep. An invalid
entry will be indicated with three beeps.
F. Programmable Maximum Call Time
The K-1900-3 can be programmed to limit the call time on the entry phone. The maximum call time is
programmable from "00" (no maximum call time) to "99" (99 minutes) and is factory set to "02" (2 minutes) (see
Programming, section D). When the call timer is enabled (programmed to "01-99"), if a call exceeds the
programmed time, both phones are provided with three beeps then disconnected, indicating the termination of
the call. This limits unnecessary and lengthy conversations. When the call timer is disabled (programmed to "00"),
there is no limit to the length of calls from the entry phone. Only a CPC disconnect signal from the telephone line,
or hanging up the entry phone will disconnect the call.
G. Built-In Toll Restriction
The K-1900-3 features built-in toll restriction. When the K-1900-3 is in the Apartment Dialer Mode (factory
setting), the unit will disconnect when it detects any Touch Tone or pulse dialing generated by the entry phone,
after speed dialing has been completed. With the K-1900-3 in the Multi-Number Dialer Mode, the unit will
disconnect when it detects any flashes or pulse dialing generated by the phone after speed dialing has been
.
completed
(factory disabled)
(00 = .5 sec, factory set to 5 sec)
6
Enter Digits
phone number +
#Q + entry code
..... 1-3 digits
............... 2 digits (00 - 99)
(CAUTION: Permanently
erases ALL programming!)
Memory
+
Location
+
#001-250
+
#001-250
+
#001-250
+
#000
+
#251-255
+
#001-255
+
##2
+
##3
+
##4
+
##5
+
##6
+
##7
Advertisement
Table of Contents
