1. Manuals
  2. Brands
  3. Hiddenbed Manuals
  4. Indoor Furnishing
  5. Double Decker
  6. Assembly instructions manual

Hiddenbed Double Decker Assembly Instructions Manual

Hide thumbs Also See for Double Decker:
Table of Contents

Advertisement

Quick Links

Download this manual
Hiddenbed
TM
ASSEMBLY INSTRUCTIONS
MODEL DOUBLE DECKER
www.hiddenbed.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Double Decker and is the answer not in the manual?

Questions and answers

Related Manuals for Hiddenbed Double Decker

Summary of Contents for Hiddenbed Double Decker

  • Page 1 Hiddenbed ASSEMBLY INSTRUCTIONS MODEL DOUBLE DECKER www.hiddenbed.com...
  • Page 2 CONGRATULATIONS! YOU ARE A PROUD OWNER OF HIDDENBED The ultimate furniture that Doubles your Space Please read carefully the Assembly Instructions. Should you have any questions please contact our authorized dealer: For further information please check www.hiddenbed.com...
  • Page 3 Follow these simple steps to assemble your Hiddenbed Put them together Assemble the 3 main parts Put the mattress in its place. LOOK, YOUR HIDDENBED IS READY!
  • Page 4 MAIN PARTS &CARPENTRY LIST BODY PARTS COMPONENTS 1a+1b 2a+2b BED PARTS COMPONENTS DESK PARTS COMPONENTS...
  • Page 5 Remember a force equivalent to lift a CRT monitor is needed to transform the bed into desk. Ask your retailer for more details. WARNINGS (!)Like a sliding door or a car door or a bike, you have to do certain things to enjoy Hiddenbed Safely and reliably. Pay attention to theses recommendations!
  • Page 6 MECHANISM KIT BOX A LOWER MECH ARM GAS SPRING LOWER SUPPORT COTTER PLATE 1100N/1300N SUPPORT BEARER LINK PIVOT 2 Pcs 2 Pcs 2 Pcs 2 Pcs 2 Pcs 2 Pcs 2 Sets ADITIONAL SAFETY DEVICE TRUNNION BUSHING & SCREW LOCK LOCK BUSHING PIN BALL 2 Sets...

  • Page 7: Body Assembly

    BODY ASSEMBLY Arm pin outer Arm pin inner position for more position for less load on table load on table RIGHT SIDE SHOWN Do the same with left side symmetrically Attach the Gas Spring end to pin ball (A11). Cotter pin Attach the Gas Spring (A2) to lower suport (A3) using Lower Support Pin(A4), insert cotter pin (A5) and bend ends.
  • Page 8 Attach Bunk Bed Slat Cleat (6) to Bunk Bed Side (4) and Body Back (5) using screw H10. Attach Body Sides (1) to Bottom Strectcher (2), Bunk Bed Side (4)and Body Back (5) fixed using dowels and screws H2. Attach Shelf Stretcher (11) to Shelf (10) using screws H14.
  • Page 9 Attach Bed Slats (15) to Bunk Bed Slats cleats using screws H10. Attach Guard Rails (7 y 8) to Bunk Bed Side and Body Back using screws H20 .

  • Page 10: Desk Assembly

    DESK ASSEMBLY Attach Desk Back (9) to Desk Top (7) with Screws H2. Screw Wood Plugs (WP) to inner side of Desk Sides(8). Attach one of the Desk Sides(8) to the Desk Top(7) using dowels and screws H2. Then insert Wood Plug into the Desk Stiffener.
  • Page 11 Attach the other Desk Side to the Desk Top using dowels and screws H2 and inserting the Wood Plug into the Desk Stiffener. Attach Tube Cover(18) to Desk Top(7) using screws H13. Attach the Tribearer(A6) to the Desk Sides(8) using screw H6, H2 and H9.

  • Page 12: Bed Assembly

    Insert locks into the Desk Sides. BED ASSEMBLY Attach Front Rail (10) and Rear Rail (11) to Bed Heads (8) with dowels and screws (H2). Be careful, put cleats inside. Perforations for Slats should be pointing bed up. (Down in sketch position!!) Slats and salt cover must be attached to the bed after the bed was attached to the body side.

  • Page 13: Final Assembly

    FINAL ASSEMBLY Assemble two Links Pivot Sets attaching three link Bushings to one triangle plate (outer cones to bushing) using Link Screws. Put bed heads bearing on desk sides carefully, aligning holes (see detail in sketch STEP 2) provided for Link bushings. In both sides in turn, place place from outside the Link Pivot Set into link holes as shown.
  • Page 14 Slide Body carefully in order to align plates with bed head holes. Then standing at rear side of Body, introduce Trunnion Bushing (A8) with screw. Screw in a few turns, and let loose. Repeat at the other side. Tighten screws (A8) strongly.
  • Page 15 From under the bed. Take out the screw of step 5. Between the Cleat of Front Rail (10) and Bed Slats (12), put edge of Wide Bed Cover (9b). Use one screw H14 to Fix Wide and Narrow Cover to one of the center slats. With the bed as shown in sketch pull all screws (H14) through the Bed Slats (12) and through Wide Bed Cover (9b) to screw in Front Rail Claet.
  • Page 16 Attach Concealers to Body Sides Using screw H10. Wait until setp 10 is done to screw the bottom part of the concealers.. Place the plastic b u s h i n g ( A 1 0 ) i n t h e concealer perforations for the locks.
  • Page 17 ASSEMBLY HAS FINISHED For Normal Use: Check that the floor is clear to lower the bed. Unlock to change from desk to bed position. Stand at the middle of the furniture to pull from bed beam and push down desk to make the transformation. The mechanism is already calibrated to work with the mattress on and a weight simiilar to 35/40 lbs.

  • Page 18: Safety Precautions

    Attach the Hiddenbed´s body to the wall using the brackets and proper wall anchors. A QUALIFIED PERSON SHOULD FIX THE HIDDENBED TO THE WALL. THE FLOOR (LEVELING AND RESISTANCE) , THE WALL (LEVELING AND RESISTANCE) AND THE FIXING (SCREWS AND ANCHORS ACCORDING TO THE WALL MATERIAL) MUST BE VERIFIED IN ORDER TO GET A SECURE FIXATION.

Table of Contents

Save PDF