Summary of Contents for Beacon Athletics Streamliner 353
Page 1
& Double Play Attachment A S S E M B L Y & U S A G E G U I D E Streamliner 70 and Streamliner 353...
Page 2
Identify your Streamliner model: A. Streamliner 70 — 4 wheels, 70 lb chalk capacity B. Streamliner 353 — 3 wheels, 35 lb chalk capacity The assembly is the same for the rear wheels and retractable handle, regardless of which model you have. Assembly for the front wheel(s) is described on the following pages for the 3-wheel and 4-wheel models.
All Models Rear Wheels & Handle A S S E M B L Y I N S T R U C T I O N S Rear wheel assembly is the same for both Streamliner models. REAR WHEELS • Tools needed: standard pliers ➊...
Front Wheel A S S E M B L Y I N S T R U C T I O N S 3-wheel Streamliner 353 ONLY (for 4-wheel model wheel assembly, go to page 6) • FRONT WHEEL Tools needed: two 3/4"...
Streamliner 70 Front Wheels A S S E M B L Y I N S T R U C T I O N S 4-wheel Streamliner 70 ONLY (for 3-wheel model wheel assembly, see previous page) • FRONT WHEELS Tools needed: Two 3/4"...
Page 8
All Models Using Your Streamliner O P E R A T I O N USING THE TELESCOPING HANDLE All Streamliners have a collapsible handle that measures 29" in height and fits easily inside an on-site storage box. To extend the handle, press the chrome spring button in on the side of the handle near the bottom. Pull up slowly on the handle until the chrome spring-button pops into the retaining hole near the top of the bottom half of the handle.
Page 9
USING THE VARIABLE FLOW CONTROL The Streamliner’s Variable Flow On/Off Control gives you total command of the flow of your dryline material. Some dryline material will flow rapidly while others flow more slowly and can “bridge” within the hopper. With this in mind, the Variable Flow Control was designed for the operator to adjust the opening according to each material’s flow rate.
Page 10
2" edge guides 4" edge guide centerline guide 4" edge guide USING THE WELDED ALIGNING GUIDE There are five guide marks welded to the front of the Streamliner frame (above, all models). The guide provides a center notch as well as edge guides for either edge of the 2" and 4" lines. Simply lay out a stringline and the Streamliner’s guide will help you maintain accurate alignment.
Page 11
H O P P E R C A P A C I T Y 3-WHEEL STREAMLINER 353 Hopper holds between 35 - 40 pounds of dry line marking material. 4-WHEEL STREAMLINER 70 Hopper holds between 70 - 75 pounds of dry line marking material.
Parts List Parts Diagram 3 - W H E E L 3 5 3 Checkmarks identify parts included with Refurbishing for Kit 353 (240-100-350). Hopper Cover [ 2 ] Inner Bearings ✓ [ 3 ] Cotter Pins Chalk Hopper ✓ [ 2 ] Clevis Pins Lower Handle and Frame [ 2 ] Large Springs...
Page 13
4 - W H E E L Checkmarks identify parts included with Refurbishing for Kit 70 (240-100-700). Hopper Cover Axle Chalk Hopper [ 2 ] Outer Bearings ✓ [ 2 ] Clevis Pins [ 2 ] Inner Bearings ✓ [ 2 ] Large Springs [ 3 ] Cotter Pins ✓...
Page 14
Double Play Aerosol Attachment A T T A C H M E N T I N S T R U C T I O N S 3-wheel 353 model and 4-wheel 70 model The optional Double Play connects to the vertical shaft of the Streamliner handle. Step 5 If your Streamliner came with the Double Play already attached, skip to set-up instructions.
Page 15
➍ Connect the trigger chain to the trigger on the handle. Slide chain through the larger hole on the trigger and pull the chain taught before locking it into the smaller hole. ➎ Insert well shaken aerosol field paint can into the Double Play. To properly position the can, make sure the T or H nozzle of the spray can is inserted so that...