Vytronix MFW1600 Instruction Manual

Vytronix MFW1600 Instruction Manual

4-in-1wet & dry vacuum, carpet washer & blower
Hide thumbs Also See for MFW1600:

Advertisement

MF W1 6 0 0 4 - I N - 1 WE T & D R Y V A C U U M,
C A R P E T WA S H E R & B L O WE R
I N S T R U C T I O N MA N U A L
w w w . v y t r o n i x . c o m

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MFW1600 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Vytronix MFW1600

  • Page 1 MF W1 6 0 0 4 - I N - 1 WE T & D R Y V A C U U M, C A R P E T WA S H E R & B L O WE R I N S T R U C T I O N MA N U A L w w w .
  • Page 2 BLANK PAGE -...
  • Page 3 BLANK PAGE -...
  • Page 4: Safety Advice

    The appliance is not suitable for use by children. • Only supplied accessories should be used. • Always consult Vytronix before attempting to carry out any repairs on the appliance beyond normal maintenance. • Check the hose for any blockage before operation.
  • Page 5: Table Of Contents

    Contents 26 . 1. Hose inlet 15. Hose main connector 2. Solution pump on/off switch 16. Hose 3. Power cord 17. Front solution tube adapter 4. Top cover 18. Rear solution tube adapter 5. Tank locking clip 19. Solution tube 6.
  • Page 6: Top Cover

    Operating In Carpet Washer Mode 1. Release tank clips, take out the top cover and remove the vacuum dust bag. 2. Insert the main hose adapter, rotate according to direction instruction and fix firmly. Then fix the front solution nozzle in anticlockwise.
  • Page 7 3. Connect the two parts of the aluminium tube together with the hose/handle. 4. Connect the wet pick-up/wash head with the aluminium tube and connect all solution tubes/fittings.
  • Page 8: Tank

    5. Release solution tank clip and remove the tank. Fill with clean, cold or warm but not hot water and solution if desired – if using solution, read the instructions on the bottle before use. PLEASE NOTE – The clean water/solution tank will hold up to 3.5L which should provide approx. 20 – 25 minutes use.
  • Page 9 PLEASE NOTE: When the pump is powered on, water will automatically begin to flow through the wash head. To stop the flow of water, the trigger must be pulled as shown below. 7. Plug in and power on the vacuum first, then switch on solution pump. IMPORTANT: always turn on the main power button first, before switching on the pump when using as a carpet washer.
  • Page 10 8. When in use, ensure that recovered/collected dirty water does not exceed the MAX fill line on the collection tank. 9. When finished, Power off the pump for 30 seconds before switching off the vacuum.
  • Page 11: Solution Tank

    10. After vacuuming, take out the solution nozzles and solution tank for cleaning. 11. Remove the top of the vacuum as shown below, empty and clean the recovery/collection tank. IMPORTANT: When removing the tubes after wet use, there may be residual fluid still in the tubes which will trickle out, it is recommended to have a container ready to collect the excess fluid to avoid spillages.
  • Page 12: Hose

    Using In Dry Vacuum Mode 1. Take out top vacuum part and install the dust bag. 2. Connect the hose onto the main inlet on the front of the vacuum. 5. Connect the two parts of the aluminium tube with the hose.
  • Page 13: Floor Brush

    6. Connect the floor brush with the tube. 7. Plug in and switch on the machine. IMPORTANT: Do not switch on the water pump. 8. After use, take out the bag and clean the dust tank.
  • Page 14 Operating The Rear Blower Function 1. Remove solution tank and take off exhaust filter cover. 2. Fix the hose into the exhaust port.
  • Page 15 3. Plug in and switch on the machine. IMPORTANT: Don’t switch on solution pump to avoid pump overheating. 4. After use, remove the hose and replace the exhaust filter cover. TOP TIP: After using as a wet vacuum or carpet washer, set up as above and use the blower function to quickly blow-dry the hose and remove any residual fluid before using the product for dry vacuuming.
  • Page 16: Product Maintenance

    Product Maintenance Check filters after each use and clean if necessary. 1. Remove the top of the vacuum cleaner. 2. Disassemble float and filter housing and clean the HEPA and sponge filters per instructions on next page. CLOSE OPEN...
  • Page 17 OPEN CLOSE OPEN CLOSE 3. Clean the filters regularly and ensure filters are completely dry before reusing. 40¡ æ 40¡ æ m ax 40¡ æ m ax m ax 24hr 4. After maintenance has been carried out/completed, reassemble all components in reverse order to which they were disassembled in steps 1 and 2.
  • Page 18: Warranty Registration

    Warranty Registration To register you free one year Vytronix warranty visit www.vytronix.com using product code: brandnew-vytronix-mfw1600 Safe Disposal This marking indicates that this product should not be disposed with other household waste throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.
  • Page 19 BLANK PAGE -...
  • Page 20 R e g i s t e r y o u r w a r r a n t y a t w w w . v y t r o n i x . c o m...

Table of Contents

Save PDF