Asco 300 Series Manual

Asco 300 Series Manual

400-800 amp quick connect power panel transfer switch accessory
Hide thumbs Also See for 300 Series:

Advertisement

Quick Connect Power Panel Transfer Switch Accessory
DANGER is used in this manual to warn of a hazard
situation which, if not avoided, will result
in death or serious injury.
WARNING is used in this manual to warn of a
hazardous situation which, if not avoided, could
result in death or serious injury.
CAUTION is used in this manual to warn of a
hazardous situation which, if not avoided, could
result in minor or moderate injury.
Important:
This manual contains information critical to the proper
installation and operation of the ASCO Series 300
Quick Connect Power Panel. Be certain to read and
understand all instructions prior to installation and
operation.
The ASCO Series 300 Quick Connect Power Panel
must be installed in conjunction with a transfer switch.
Limited Warranty
When this ASCO Series 300 Quick Connect Power Panel
is installed and operated according to the manual's
instructions ASCO Power Technologies will repair or
replace any of its mechanical or electrical parts if they are
found to be defective in material or workmanship within two
year of the purchase date.
Florham Park, NJ 07932-1591
Series 300
400-800 Amp
Maintenance
The ASCO Series 300 Quick Connect Power Panel will
require periodic maintenance. ASCO Power Technologies
recommends annual inspections to keep the panel in safe
operating condition. ASCO Power Technologies
recommends that the Pre-Operation and Maintenance
Checklist under Appendix A serve as a basis for annual
inspection.
Technical Support
ASCO Power Services are available to assist in resolving
issues by calling 1-800-800 2726 (ASCO) or emailing
powerwarranty@ascopower.com. For any other
information, please refer to ascopower.com
381333-464
www.ascopower.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 300 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Asco 300 Series

  • Page 1 400-800 Amp Quick Connect Power Panel Transfer Switch Accessory Maintenance The ASCO Series 300 Quick Connect Power Panel will DANGER is used in this manual to warn of a hazard require periodic maintenance. ASCO Power Technologies situation which, if not avoided, will result recommends annual inspections to keep the panel in safe in death or serious injury.
  • Page 2: Table Of Contents

    ASCO Series 300 Quick Connect Power Panel Contents Page(s) Section Limited Warranty Maintenance Technical Support Prior to Installation Shipment: Unpacking and Inspection Installation Set-up Disconnecting Circuits Appendix Pre-Operation and Maintenance Checklist 381333-464 www.ascopower.com...
  • Page 3: Prior To Installation

    3/8“ fasteners (See Figure 1). may result. The surface where the ASCO Series 300 Quick Connect Perform a visual inspection to ensure the door and handle are in functioning condition and that the panel integrity is...
  • Page 4: Installation

    ASCO Series 300 Quick Connect Power Panel Installation 1. Open upper to door to expose dead front panel The installation of the ASCO Series 300 Quick 2. Unfasten the dead front panel by removing the four (4) Connect Power Panel should be carried out by Phillips- headed 10-32 x 1/2”...
  • Page 5 2. Beginning with the ground, strip and install the cables wired clockwise or counter-clockwise in the appropriate compression terminals 2. Apply the provided label to the inside of the ASCO Series 300 Quick Connect Power Panel on the inside of the cam connection chamber door. (Figure 4)
  • Page 6: Set-Up

    ASCO Series 300 Quick Connect Power Panel Set-up 4. Complete the Neutral (white) connection Step 6: Review Pre-Operation Checklist under Proper connection (See Figure 5): Appendices A prior to operation (pg. 8) A. Grasp connector jacket and firmly Insert cam connector into cam plug B.
  • Page 7: Disconnecting Circuits

    ASCO Series 300 Quick Connect Power Panel Set-up – Continued Step 10: Powering Up Complete disconnect of ALL hot connections prior to proceeding Power MUST BE supplied from a single generator 5. Disconnect the Neutral (white) connection. Start generator per manufacturer instructions Proper disconnection (See Figure 5): 2.
  • Page 8 Do not use cables if any copper wiring is exposed – 6. ASCO Power Services are available to assist in resolving issues. If you have any questions or need technical advice or suggestions regarding this product, please contact ASCO Power Technologies at 1-800-800-2726(ASCO) or e-mail powerwarranty@ascopower.com...

Table of Contents