Connecting The Device - WAGNER Control Pro 150 Operating Instructions Manual

Control Pro 150
Secure device and spray gun
All hoses, fittings, and filter parts must be secured
before operating spray pump. Unsecured parts
can eject at great force or leak a high pressure fluid
stream causing severe injury.
Always secure the spray gun when mounting or
dismounting the nozzle and in case of interruption to
work.
Recoil of spray gun
In case of high operating pressure, pulling
the trigger can effect a recoil force of up
to 15 N.
Danger
If you are not prepared for this, your
hand can be thrust backwards or your
balance lost. This can lead to injury.
Continuous stress from this recoil can
cause permanent damage to health.
Max. operating pressure
Max. permissible operating pressure for spray gun,
spray gun accessories and high-pressure hose may
not fall short of the maximum operating pressure of
110 bar (11 MPa) stated on the unit.
Coating substance
Caution against dangers that can arise from the sprayed
substance and observe the text and information on the
containers or the specifications given by the substance
manufacturer.
Do not spray any liquid of unknown hazard potential.
High-pressure hose (safety note)
Attention, danger of injury by injection!
Wear and tear and kinks as well as usage
that is not appropriate to the purpose
Danger
of the device can cause leakages to form
in the high-pressure hose. Liquid can be
injected into the skin through a leakage.
High-pressure hoses must be checked thoroughly before
they are used.
Replace any damaged high-pressure hose immediately.
Never repair defective high-pressure hoses yourself!
Avoid sharp bends and folds: the smallest bending radius
is about 20 cm.
Do not drive over the high-pressure hose. Protect against
sharp objects and edges.
Never pull on the high-pressure hose to move the device.
Do not twist the high-pressure hose.
Do not put the high-pressure hose into solvents. Use only
a wet cloth to wipe down the outside of the hose.
Lay the high-pressure hose in such a way as to ensure
that it cannot be tripped over.
Electrostatic charging of spray guns and the high-
pressure hose is discharged through the high-pressure
hose. For this reason the electric resistance between the
connections of the high-pressure hose must be equal or
lower than 197 kΩ/m (60 kΩ/ft.).
For reasons of function, safety and
i
durability, only use genuine WAGNER
high-pressure hoses and spray nozzles.
For overview see „Spare parts lists".
The risk of damage rises with the age of
i
the high-pressure hose.
Wagner recommends replacing high-
pressure hoses after 6 years.

Connecting the device

A properly earthed socket outlet with earthing
contact must be used for connection. The connection
must be equipped with a residual current protective
device with INF ≤ 30 mA.
Setting up the unit
When working indoors:
Vapors containing solvents may not be
allowed to build up in the area of the
Danger
device.
Setting up the unit on the side a way
from the sprayed object.
A minimum distance of 5 m between the
unit and spray gun is to be maintained.
When working outdoors:
Vapors containing solvents may not be
allowed to blow toward the unit.
Note the direction of the wind.
Set the unit up in such a way that vapors
containing solvents do not reach the unit
and build up there.
A minimum distance of 5 m between the
unit and spray gun is to be maintained.
Maintenance and repairs
Before carrying out any work on the device,
relieve the pressure and unplug the power
plug from the socket.
Danger
Cleaning the unit
Danger of short circuit through
penetrating water!
Never spray down the unit with high-
Danger
pressure or high-pressure steam
cleaners.
Cleaning units with solvents
When cleaning the unit with solvents,
the solvent should never be sprayed or
pumped back into a container with a
small opening (bunghole). An explosive
Danger
gas/air mixture can be produced. The
container must be earthed.
Do not use flammable materials for
cleaning purposes.
AUS
5