ADT Safewatch Pro 3000 System Manual page 2
Hide thumbs
Also See for Safewatch Pro 3000:
- User manual (57 pages) ,
- Installaton manual (88 pages) ,
- Programming manual (16 pages)
Table of Contents
Advertisement
Safewatch Pro 3000 System Manual
Multiple partition arming/disarming
Up to four programmable pagers
System scheduling
The Safetwatch Pro 3000 is designed to be as maintenance free as possible, however we suggest that you
still test your system once a month and after any alarm occurrences.
Treat the system as you would any other electrical equipment; do not slam protected doors or windows,
keep dust from accumulating on the touchpad and sensors, and do not spray water or any liquid on the
units.
*Your system may or may not be set up for fire protection.
System Keywords
Keyword
Meaning
Alarm
An alarm has been detected in the armed system. See zone area number(s) to identify
location of triggered alarm.
Away
All burglary zones, interior and perimeter, are armed.
Instant
Perimeter burglary zones are armed and entry delay is turned off.
Stay
Perimeter burglary zones, such as protected windows and doors, are armed.
Fire
Appears when a fire alarm or fire fault is present. Accompanied by a display of the zone
in alarm.
Bat
Low battery condition in a wireless sensor if zone number is displayed or low system
battery if no zone number is displayed.
Chime
Appears when the Chime feature is activated.
Bypass
Arming the system with protected areas intentionally left open.
Check
A malfunction has occurred. See area zone number to identify location of trouble event.
No AC
AC power has been cut off and the system is running on backup battery.
Not Ready
System not ready for arming. READY indicates the system is ready.
Arm & Disarm the System
When arming your system it is important to note that:
Before arming your system, all protected areas must be closed. Use the READY/[*] key to display
any faulted (i.e., open) zones. The system will display READY when the system is ready to be armed.
Codes and commands must be within of 10 seconds of each other. If more than 10 seconds elapse
between entries, the entry will be aborted and must be re-entered.
https://alpha.adt.com/help/63[11/12/2018 9:41:21 PM]
Hide quick links:
Advertisement
Table of Contents
Need help?
Do you have a question about the Safewatch Pro 3000 and is the answer not in the manual?
Questions and answers
How to pull out from wall to add board behind it
Based on the provided context, there are instructions for mounting a circuit board in the ADT Safewatch Pro 3000 system but no direct steps for removing the entire unit from the wall. However, generally, to remove the ADT Safewatch Pro 3000 from the wall to add a board behind it, follow these steps:
1. Power Down the System – Disconnect the system from power and remove the backup battery to avoid electrical hazards.
2. Remove the Keypad or Cover – If applicable, detach the keypad or outer cover by loosening screws or using a release clip.
3. Unscrew the Mounting Screws – Locate and remove any screws securing the unit to the wall.
4. Gently Pull the Unit Away – Carefully pull the system from the wall, ensuring no wires are damaged.
5. Access the Mounting Area – Once removed, you can insert the board behind it as needed.
If securing a new circuit board inside the cabinet, follow the instructions to insert the top of the board into the slots and secure it using the mounting clips and screws.
This answer is automatically generated
I found no method in the manual to permanently display the date and time. Is there a procedure to do this?
You cannot permanently display the date and time on the ADT Safewatch Pro 3000. The system allows viewing the current date and time temporarily by pressing a programmed function key (A, B, C, or D), and the display remains on for about 30 seconds.
This answer is automatically generated
What does the code FC mean on the display?
The FC code on the ADT Safewatch Pro 3000 display indicates a communication failure between the security system and the monitoring center.
This answer is automatically generated