Summary of Contents for Farmi Forest Corporation VALBY HF 231
Page 1
www.normet.fi 03299760 A- -USA- -200802- -JaK HF 231 OPERATION, MAINTENANCE AND SPARE PARTS MANUAL 03294709 HYDRAULIC FEEDER AND FEED CHUTE HF231 From machine: 329 4036-- It is very important to read this instruction handbook thoroughly before using the machine! Normet Corporation Ahmolantie 6 FIN---74510 PELTOSALMI FINLAND...
www.normet.fi HF 231 03294709 SAFETY INSTRUCTIONS 1. TERMS AND SYMBOLS USED IN INSTRUCTIONS Safety is a combination of operator com- THINK mon sense and alertness at all times SAFETY! when the machine is being operated or serviced. This message is used for general remind- CAUTION! ers of good safety practices or to direct attention to unsafe practices.
www.normet.fi HF 231 03294709 SAFETY INSTRUCTIONS 2.SAFETY 2.1.GENERAL SAFETY Do not operate this machine until you have read and IMPORTANT! understood the manual page by page. The owner of this machine is responsible for instructing all operators and support personnel in the operation and safety precautions of this chipper.
www.normet.fi HF 231 03294709 SAFETY INSTRUCTIONS Disengage the PTO, cut the engine and remove the keys before any mainte- D D D D nance. Use only original parts replacements. IMPORTANT! Do not make any modifica- D D D D tions. D D D D Check all moving parts.
www.normet.fi HF 231 03294709 SAFETY INSTRUCTIONS 2.3.SAFETY INSTRUCTIONS FOR THE HYDRAULIC UNIT D D D D Before performing lubrication work on any equipment, consult the manufac- turer’s instruction manual and follow the recommended procedures. D D D D Before lubricating the machine, shut down the engine and stop the ma- chine.
www.normet.fi HF 231 03294709 PRESENTATION 3.2. MAIN COMPONENTS 3. FEED CHUTE PRESENTATION 1.Control lever 2.Directional valve 3.1. FIELD APPLICATION 3.Flow regulator The hydraulic feed chute HF231 makes feeding 4.Hydraulic motors difficult material easier and more effective. The chip quality improves due to constant feeding 5.Feed rollers speed and is less dependent on knives sharp- 6.Frame...
www.normet.fi HF 231 03294709 ASSEMBLY AND MOUNTING 3.Hook up the control rods extension with the 4. ASSEMBLY AND MOUNTING pin. 4.Connect hydraulic hoses; Connect pressure 1.Fasten the frame of the hydraulic feed to the hose (marked ”IN”) to tractors hydraulic con- chipper with two hinge pins.
Page 12
www.normet.fi HF 231 03294709 ASSEMBLY AND MOUNTING Before change Plug After change Serial nipple Pressure order no. 52435732 Plug Return order no.52080207 Fig.5. Changing the valve for closed center hydraulics. D Instructions for connecting the hydraulics when using the optional hydraulic unit can be found in hydraulic units mounting instruc- tions.
www.normet.fi HF 231 03294709 OPERATION AND MAINTENANCE tinue feeding by pushing the rod to FEED 6. OPERATION position. D In case you must remove the tree from the 6.1. CONTROLS feed chute during chipping, push the rod to REVERSE position and keep it there until the HF231 is operated with an operating handle which feedrollers release the tree.
www.normet.fi HF 231 03294709 OPERATION AND MAINTENANCE D Check and tighten possibly loose screws and 7. MAINTENANCE nuts often. D Take care that the oil in the hydraulic system D All bearings in the feed system are perma- is clean. Dirt may damage valves and hydrau- nently lubricated and do not need any further lic motors.
www.normet.fi HF 231 03294709 SPARE PARTS 56046154 Control valve, complete Part Order no. Description Remarks Qty..56046204 ..Inlet section, complete ... . See separate spare parts list .
www.normet.fi HF 231 03294709 SPARE PARTS 58101551 Work section, complete Part Order no. Description Remarks Qty..58101627 ..Seal retainer plate ..........
Page 25
www.normet.fi HF 231 03294709 SPARE PARTS 56040215 Outlet section, complete, new model Part Order no. Description Remarks Qty..58101633 ..Housing ............
Page 26
www.normet.fi HF 231 03294709 SPARE PARTS 56040215 Outlet section, complete, old model Part Order no. Description Remarks Qty..58101633 ..Housing ............