Table of Contents
Advertisement
Quick Links
EN
The installation, use and maintenance Manual (hereinafter Manual) provides the user with information
necessary for correct and safe use of the machine (hereinafter "machine", "refrigerator" or "appliance").
The following must not be considered a long and exacting list of warnings, but rather a set of instructions
suitable for improving machine performance in every respect and, above all, preventing injury to persons
and animals and damage to property due to improper operating procedures.
All persons involved in machine transport, installation, commissioning, use and maintenance, repair and disassembly
must consult and carefully read this manual before carrying out the various operations, in order to avoid wrong and
improper actions that could compromise the machine's integrity or endanger persons. Make sure to periodically inform
the appliance user regarding the safety regulations. It is also important to instruct and update personnel authorised to
operate on the machine, regarding its use and maintenance.
The manual must be available to operators and carefully kept in the place where the machine is used, so that it is
always at hand for consultation in case of doubts or whenever required.
If, after reading this manual, there are still doubts regarding machine use, do not hesitate to contact the Manufacturer or
the authorised after-sales service centre, to receive prompt and precise assistance for better operation and maximum
efficiency of the machine.
During all stages of machine use, always respect the current regulations on safety, work hygiene and environmental
protection. It is the user's responsibility to make sure the machine is started and operated only in optimum conditions
of safety for persons, animals and property.
The manufacturer declines any liability for operations carried out on the appliance without respecting the
instructions given in this manual.
No part of this manual may be reproduced.
Foreword
27
Advertisement
Table of Contents
Related Manuals for Electrolux GP379
Summary of Contents for Electrolux GP379
- Page 1 Foreword The installation, use and maintenance Manual (hereinafter Manual) provides the user with information necessary for correct and safe use of the machine (hereinafter “machine”, “refrigerator” or “appliance”). The following must not be considered a long and exacting list of warnings, but rather a set of instructions suitable for improving machine performance in every respect and, above all, preventing injury to persons and animals and damage to property due to improper operating procedures.
-
Page 2: General Information
IP21 recognise and prevent any risks. His professionalism covers the Electrolux Professional SPA - Viale Treviso, 15 - 33170 Pordenone (Italy) mechanical, electrotechnical and electronics fields. The dataplate gives the product identification and technical data. -
Page 3: Personal Protection Equipment
The employer, workplace manager or service technician are responsible for identifying and choosing adequate and suitable personal protection equipment to be worn by operators, in compliance with regulations in force in the country of use. Electrolux Professional SPA declines any liability for any... -
Page 4: Technical Data
4 compartments A.2 TECHNICAL DATA Weight Temp. range in compartment °C -2/+10 A.2.1 MATERIALS AND FLUIDS USED Max. room temp era ture °C The areas in contact with the product are in steel or coated with non-toxic plastic material. An HFC (R134a(GWP:1430)/ - Recommended condensing unit for counter 2/3 compartments R404a(GWP:3922)) refrigerant fluid complying with the current... -
Page 5: Transport, Handling And Storage
B.1 TRANSPORT, HANDLING AND STORAGE ATTENTION! Do not push or pull the appliance to move it, as it may tip over. B.1.1 INTRODUCTION Transport (i.e. transfer of the machine from one place to another) B.1.6 PLACING THE LOAD and handling (i.e. transfer inside workplaces) must occur with the Before placing the load, make sure the way is free and that the use of special and adequate means. - Page 6 can operate is +43°C. it is advisable to install the remote unit at a max. pipe length The machine must be taken to the place of installation and the of between 15 m and 20 m from the appliance. packing base removed only when being installed. NOTE: If the distance exceeds 20 m, ask the technical depart- Arranging the machine: ment for details or use a more powerful refrigeration unit.
-
Page 7: Control Panel
• After making the connection, with the machine running check that the power supply does not fluctuate by ±10% the rated ATTENTION! voltage. When replacing the cable, the earth wire must be kept longer than the live and neutral wires. Note: In models arranged for operation with remote units, make If the power cable is damaged, it must be replaced by the service centre or in any case by qualified personnel, in... -
Page 8: Position Display
- Manual defrost activation Maximum pos. - 2 °C Minimum pos. = + 10 °C Keep the “DOWN” button pressed for at least 5 seconds Maximum pos. = - 15°C to start a manual defrost cycle. Minimum pos. = - 20°C This function is signalled by lighting up of the DEFROST icon C.1.5 DIGITAL THERMOSTAT ICONS The digital thermostat has 5 signalling ICONS:... - Page 9 C.3.3 SAFETY SIGNS TO BE PLACED ON THE MACHINE OR Reasonably foreseeable improper use includes: NEAR ITS AREA • lack of machine maintenance, cleaning and periodical checks; • structural changes or modifications to the operating logic; PROHIBITION MEANING • tampering with the guards or safety devices; •...
-
Page 10: Normal Machine Use
D.1.1.2 Cleaning the cabinet and accessories C.4 NORMAL MACHINE USE Be fo re us ing the appli ance, cl e an all the in si de pa rts an d ac ces- sor ies wi th lukewa rm wa ter an d ne ut ral so ap or pr odu cts th at C.4.1 CHARACTERISTICS OF PERSONNEL TRAINED FOR are over 90% bio degra dable (in order to reduce the emission of NORMAL MACHINE USE... - Page 11 ATTENTION! appliance identi cation code Put the machine in safe conditions before starting any maintenance operation. PNC 728304 23 After carrying out maintenance make sure the machine is able to work safely and, in particular, that the protection and safety 10th piece devices are efficient.
-
Page 12: Machine Disposal
ATTENTION! D.2 MACHINE DISPOSAL Machine maintenance, checking and overhaul op- erations must only be carried out by a specialised ATTENTION! Technician or the After-Sales Service, provided DISMANTLING OPERATIONS MUST BE CARRIED with adequate personal protection equipment OUT BY QUALIFIED PERSONNEL. (safety shoes and gloves), tools and ancillary means.