Download Print this page

Honeywell HLR1001 User Manual

Ip over coax converter
Hide thumbs

Advertisement

Quick Links

Video
IP over Coax Converter HLR1001
User's Manual
Important Safeguards and Warnings
Attention
Please read the following safeguards and warnings carefully before using the product in
order to avoid damages and losses.
Note:
Do not expose the device to steam or dust. Otherwise it may cause fire or electric
shock.
Do not install the device at position exposed to sunlight or in high temperature.
Temperature rise in device may cause fire.
Do not expose the device to humid environment. Otherwise it may cause fire.
The device must be installed on solid and flat surface in order to guarantee safety
under load. Otherwise, it may cause device to fall off or turnover.
Do not place the device on carpet or quilt.
Do not block air vent of the device or ventilation around the device. Otherwise,
temperature in device will rise and may cause fire.
Do not place any object on the device.
Do not disassemble the device without professional instruction.
Do not use power line other than the one specified. Please use it properly. Otherwise,
it may cause fire or electric shock.
Special Announcement
This manual is for reference only.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website for more information.
The function of the ITE being investigated to IEC 60950-1 is considered not likely to
require connection to an Ethernet network with outside plant routing, including
campus environment.
The installation instructions clearly state that the ITE is to be connected only to PoE
networks without routing to the outside plant.
Caution
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Regulatory Statements
FCC Statement of Compliance
Information to the User: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Note Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
apparatus complies with Canadian ICES-003.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant
with the European Parliament and Council Directive on the Restrictions of the use of
certain hazardous substances in electrical and electronic equipment (2011/65/EU),
General Product Safety Directive (2001/95/EC), and the essential requirements of the
EMC
Directive (2014/30/EU), conforming to the requirements of standards EN 55032 for
emissions, EN 50130-4 for immunity, and EN 60950-1 for electrical equipment safety.
Manufacturer's Name and Address
Honeywell Security(China) Co., Ltd. Building 21, 22,28, Section 2, Huaide Cuigang
Industrial Estate, Fuyong, Bao'an District, ShenZhen, China.
Waste Electrical and Electronic Equipment (WEEE)

Product Overview

Product Introduction
IP over Coax Converter is a type of converter from RJ45 to BNC port, which supports
long range power supply transmission via coaxial cable. It provides one BNC coaxial port
and one RJ45 port.
The product is equipped with two transmission modes which are 100Mbps and 10Mbps.
It can be modified according to the transmission distance.
Product Features
Supports IEEE802.3, IEEE802.3u and IEEE802.3X standards.
Supports IEEE802.3af and IEEE802.3at power supply standards.
Port: 1*RJ45 10/100Mbps, 1*BNC.
Supports RG59 coaxial cable: 400m/100Mbps, 1000m/10Mbps.
Supports MDI/MDIX self-adaption.
Supports long range power supply transmission via coaxial cable.
Operating temperature: -30~65℃.

Typical Application

The product is divided into transmitter (HLR1001-T) and receiver (HLR1001-R), and its
networking scheme is shown as Figure 1:
Figure 1
Device Structure
Device Panel
The device panel is shown in Figure 2 (HLR1001-T) and Figure 3 (HLR1001-R).
Figure 2
Figure 3
Please refer to Table 1 for more details.
This Class A digital
Table 1
SN
1
2
3
4
5

Installation Guide

Device Installation
IP over Coax Converter supports two installation modes. It can be installed into the
junction box or it can support DIN rail mount.
Please refer to Figure 4 for the installation inside junction box.
1
Correct Disposal of this Product (applicable in the European Union and other European
countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.
Name
Note
PoE OUT
PoE output port
PoE IN
PoE input port
BNC port Link indicator light
Link
E100: On for 3 seconds, off for 1 second
E10: On for 1 second, off for 1 second
PWR
Power indicator light
Long Reach
Coaxial cable port

Advertisement

loading

  Related Manuals for Honeywell HLR1001

  Summary of Contents for Honeywell HLR1001

  • Page 1: Product Overview

    The installation instructions clearly state that the ITE is to be connected only to PoE Device Panel networks without routing to the outside plant. The device panel is shown in Figure 2 (HLR1001-T) and Figure 3 (HLR1001-R). Caution Figure 2 This is a Class A product.
  • Page 2 • Please visit our website for more information. Please refer to Figure 5 for DIN rail mount. Figure 5 Honeywell Security Products Americas (Head Office) 2700 Blankenbaker Pkwy, Suite 150 Louisville, KY 40299, USA www.honeywell.com/security  +1 800 323 4576 Honeywell Security Europe/South Africa AppendixⅠTechnical Specifications...
  • Page 3 Document 800-24173 – Rev C – 04/2018 © 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof.

This manual is also suitable for:

Hlr1001-rHlr1001-t