Table of Contents
Advertisement
Quick Links
ProTrax
Multi-Angle Saw Tables
& MaxTrax
™
Operating Instructions
Revision 2 - 5/04
saw table with oversized work surface
Table of Contents
General Instructions ..............................1
Setting up your ProTrax ........................2
Installing the Fence Tape .......................5
Attaching Deck Extender .......................5
90 Degree Cuts ...................................6
Angle Cutting ......................................7
Cutting a 3/12 Pitch ............................8
Setting up your MaxTrax .......................9
90 Degree Cuts ...................................9
Angle Cutting and 3/12 Pitch ........... 10
Trouble Shooting ................................. 11
™
Advertisement
Table of Contents
Related Manuals for Tapco ProTrax
Summary of Contents for Tapco ProTrax
-
Page 1: Table Of Contents
Multi-Angle Saw Tables Operating Instructions saw table with oversized work surface Table of Contents General Instructions ......1 Setting up your ProTrax ......2 Installing the Fence Tape .......5 Attaching Deck Extender .......5 Using the ProTrax 90 Degree Cuts ........6 Angle Cutting ........7 Cutting a 3/12 Pitch ......8... -
Page 2: General Instructions
(circular saw not included) Care & Maintenance: Routine care and maintenance Transportation: When transporting, remove the saw is required to keep your ProTrax and MaxTrax Saw and the boom from the table. Remove table from the Table functioning properly. The Lock Block and stand. -
Page 3: Setting Up Your Protrax
Work Surfaces in place. unlock Work Surfaces. STeP 1 STeP 2 With the ProTrax and MaxTrax Saw Table removed from the Orient the Lock Block to box, secure it on either saw horses or the optional Snap Stand. the position shown above. - Page 4 P r o T r a x & M a x T r a x S a w T a b l e s Setting Up Your ProTrax and MaxTrax Saw Tables (continued) GUArD ConTACTInG ToP oF GrooVe STeP 4...
- Page 5 & M a x T r a x S a w T a b l e s Setting Up Your ProTrax and MaxTrax Saw Tables (continued) STeP 8 The fence on each side of the table is held in place with a spring button that projects through a hole in the middle of the fence.
-
Page 6: Installing The Fence Tape
P r o T r a x & M a x T r a x S a w T a b l e s Installing the Fence Tape on Your ProTrax and MaxTrax Saw Tables Peen Here FenCe TrACk TrIM oFF... -
Page 7: Using The Protrax 90 Degree Cuts
Using the ProTrax Multi-Angle Saw Table: 90 Degree Cuts STeP 1 STeP 2 The ProTrax Saw Table can cut pitches as low as To square the Boom with the Work Surfaces, simply 4/12 in either direction. A pitch of 3/12 can only be slide two of the Work Surfaces up against the Boom. -
Page 8: Angle Cutting
M a x T r a x S a w T a b l e s Using the ProTrax Multi-Angle Saw Table: Angle Cutting STeP 1 - example of setting 6/12 SeT 3/12 & 4/12 wITH Slide the work surfaces away from the Boom. The... -
Page 9: Cutting A 3/12 Pitch
M a x T r a x S a w T a b l e s Using the ProTrax Multi-Angle Saw Table: Cutting a 3/12 Pitch 3/12 pitch can only be set from the left side of the table. 3/12 PITCH STeP 1 Slide the work surfaces away from the Boom. -
Page 10: Setting Up Your Maxtrax
MaxTrax and must be followed. Using the MaxTrax Multi-Angle Saw Table: 90 Degree Cuts Follow Steps 1-5 of “Using the ProTrax Multi-Angle Saw Table: 90 Degree Cuts” (page 6). The MaxTrax has Deck Extenders that need to be against the Boom when cutting. -
Page 11: Angle Cutting And 3/12 Pitch
T a b l e s Using the MaxTrax Saw Table: Angle Cutting and 3/12 Pitch Follow Steps 1-3 of “Using the ProTrax Multi-Angle Saw Table: Angle Cutting” (page 7) or “Using the ProTrax Multi-Angle Saw Table: Cutting 3/12 Pitch”... -
Page 12: Trouble Shooting
M a x T r a x S a w T a b l e s Trouble Shooting Your ProTrax and MaxTrax Saw Tables 2) Remove the set screw and tighten or loosen the 1) The locking block is preset at the factory. If the Lock Block to adjust the tension of the handle.
Need help?
Do you have a question about the ProTrax and is the answer not in the manual?
Questions and answers