No
Function
Button name
・
Press the CD OPEN/CLOSE button to open the
tray.
・
Set a disc on the tray, then press the CD OPEN/
CLOSE button again to close the tray. The disc is
6.1 Disc loading
mounted automatically.
Move the slide to the initially set position (10 mm
・
towards the outside from the innermost position)
and stop in this status.
Press the CD PLAY/PAUSE button. Execute the
・
following steps.
①
LD ON (with servo still stopped)
FOCUS ON (disc rotation, tracking off)
②
If no disc loaded, retry then stop.
③
CLV ON
TRACKING ON
④
⑤
SUB CODE readout (playback sound output)
When display is as in
and the PLAY button
⑥
⑤
is pressed, conduct BER (Block Error Rate)
display for 2 seconds. (Display total no.
generated in 10 seconds.)
Press the PLAY button continuously for over 1
*
second to switch directly to SUB CODE
readout in step
⑤ .
6.2 Servo check
・
In the stop mode, pickup moves in REV (inwards)
or FWD (outwards) direction when the
button or the
button pressed.
When the
button pressed, move to stop
・
6.3 Pickup movement
operation after detection that inner switch has
turned on.
Pickup movement stops when button released.
・
(Pickup moves while button is pressed.)
When the STOP button is pressed, play operation
・
6.4 Stop
and servo stop.
After stopping, conduct reading of auto adjust values.
・
When the FUNCTION button is pressed for over
・
2 seconds, all servos turn on, auto adjustment is
performed and switch to playback operation.
6.5 All servo on
(Playback sound output)
Display
Continue S6 display
・
flashing
①
②
③
④
⑤
@@
: T.No
XX:XX
: Time
⑥
###### : B.E.R.
Continuous display of previous time
Same as S6.
・
flashing
・
@@
: T.No
XX:XX
: Time
No
キー名称
・CD OPEN/CLOSE ボタンでトレイを開く.
・ディスクを置き、再度 CD OPEN/CLOSE ボタンでトレイ
を閉じるとディスクをチャッキングする.
6.1
ディスク装着
・スライドを初期設定位置(最内周から外側
10mm の位置)に移動し、その状態でストップ
する.
・CD PLAY/PAUSE ボタンを押すと下記ステップを実
行する.
① LD ON( サーボ停止のまま )
② FOCUS ON( ディスク回転、トラッキング OFF)
ディスク無しの場合、リトライ後停止する.
③ CLV ON
④ TRACKING ON
⑤ SUB CODE 読み出し(再生音出力)
⑥ ⑤の表示時に PLAY ボタンを押すと、2 秒間
BER(Block Error Rate) の表示を行なう.
(10 秒間の間に発生した総数を表示)
* PLAY ボタンの 1 秒以上押し続けにて、ダイレクト
に⑤の SUB CODE 読み出しステップに移行する.
6.2
サーボチェック
・ストップ状態で
押すと、ピックアップが REV( 内周側 ) または
FWD( 外周側 ) 方向に移動する.
6.3
ピックアップ移動
・
ボタンを押した時は、内周 SW の ON を
検出後ストップ動作に移行する.
・ボタンを離すとピックアップの移動を停止する.
( ボタンが押されている間、移動する.)
・STOP ボタンを押すと、PLAY 動作及びサーボを停
6.4
停止
止する.
・停止後、自動調整値の読込みを行なう.
・FUNCTION ボタンを 2 秒以上の長押しすると全
サーボを ON し、自動調整を行なって再生動作
に移行する. (再生音出力)
6.5
全サーボ ON
12
機能
表示
S6 の表示を継続する.
・
を点滅
①
②
③
④
⑤
@@
:T.No
XX:XX :時間
⑥
###### :B.E.R.
ボタンまたは
ボタンを
前回の表示を継続する.
・S6 と同じ.
・
を点滅
@@
:T.No
XX:XX :時間
S-81/S-81DAB