Related Manuals for Dell EMC N20 Series
Summary of Contents for Dell EMC N20 Series
- Page 1 Dell Networking OS Conversion Guide for the N20xx/N30xx Series From Version 6.3.x.x to 9.11.x.x and from Version 9.11.x.x to Version 6.3.x.x...
- Page 2 Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
-
Page 3: Table Of Contents
Contents 1 About this Guide.............................4 Before you Begin................................5 Finding your Digital Product on Dell Digital Locker......................5 2 Convert a Dell N20xx or N30xx series Switch to a Port Extender..............6 Upgrading the Device to the Latest Dell Networking OS Version 6.3.x.x..............6 Installing Dell Networking OS 9.11.x.x on the Device......................7 3 Convert an N-series Port Extender to a Dell N20xx or N30xx Switch............ -
Page 4: About This Guide
About this Guide This document provides instructions for converting a Dell N20xx or N30xx series platform to a Rapid Access Node (RAN) so that you can use it as a port extender (PE) with a C9010 switch. Conversely, the document also provides instructions to revert a converted port extender to an N20xx or an N30xx-series switch. -
Page 5: Before You Begin
Before you Begin Before you begin, ensure that you perform the following actions: • Before proceeding, upgrade the C9010 to Dell Networking OS version 9.11(0.0) or later. • Before converting the N20xx or N30xx switch to a port extender, upgrade the N20xx or N30xx switch to Dell Networking OS version 6.3.0.16 or later. -
Page 6: Convert A Dell N20Xx Or N30Xx Series Switch To A Port Extender
Convert a Dell N20xx or N30xx series Switch to a Port Extender Converting a Dell N20xx or N30xx-series switch to a port extender is a two-step process. Upgrade the device to the latest Dell Networking OS version 6.3.x.x. Install the Dell Networking OS version 9.11.0.0 on the device. NOTE: Dell Networking recommends upgrading the C9010 to the latest Dell Networking OS version before converting an N20xx or N30xx device to a PE. -
Page 7: Installing Dell Networking Os 9.11.X.x On The Device
Machine Description....Dell Networking Switch System Model ID....N3024P Machine Type...... Dell Networking N3024P Serial Number..... CN0C3M5M2829856B0126A03 Manufacturer...... 0xbc00 Burned In MAC Address..... F8B1.5682.DD45 System Object ID....1.3.6.1.4.1.674.10895.3059 SOC Version....... BCM56342_A0 HW Version......5 CPLD Version...... 13 unit active backup current-active next-active ---- ----------- ----------- -------------- -------------- 6.1.1.7... - Page 8 Management access will be blocked for the duration of the transfer Are you sure you want to start? (y/n) y If you are using Dell Networking OS 6.3.1.x: console#copy ftp://username@10.16.127.36/NSeriesRANsw.tgz application Remote Password:******** Transfer Mode........FTP Server IP Address......10.16.127.36 Source File Path.......
-
Page 9: Convert An N-Series Port Extender To A Dell N20Xx Or N30Xx Switch
Convert an N-series Port Extender to a Dell N20xx or N30xx Switch You can convert an N-series port extender back to a Dell N20xx or N30xx switch with Dell Networking OS version 6.3.x.x. You can convert only one PE at a time using the upgrade system-image-os6. If you have a PE stack setup, Dell Networking recommends the following order of conversion to avoid unnecessary stack membership reelections: Convert all member units. - Page 10 !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! PE (11/0) Image upgraded successfully. The system reboots and installs Dell Networking OS version 6.3.0.16. After installation, the system displays the console> prompt on the console. Verify if the installation is successful. console>show version Machine Description....Dell Networking Switch System Model ID....