Advertisement
Available languages
Available languages
16 | English
Workpiece shape
0°
100 x 100
158 x 80
110 x 110
Minimum workpiece dimensions
(= all workpieces that can still be clamped in place with the
locking spindle (7)): Length 80 mm
Max. cutting depth (0°/0°): 115 mm
Dust/chip extraction (see figure H)
The dust from materials such as lead paint, minerals and
metal can be harmful to human health. Touching or breath-
ing in this dust can trigger allergic reactions and/or cause
respiratory illnesses in the user or in people in the near vicin-
ity.
Certain kinds of metal dust are hazardous, especially in com-
bination with alloys such as zinc, aluminium or chrome. Ma-
terials containing asbestos may only be machined by special-
ists.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
The saw blade (31) can become blocked by dust, chips or
workpiece fragments in the recess of the saw table (25).
– Switch the power tool off and pull the mains plug out of
the socket.
– Wait until the saw blade has come to a complete stop.
– Pull out the chip drawer (24) and empty it completely.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Starting operation
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power tool.
Products that are only sold in AUS and NZ: Use a resid-
u
ual current device (RCD) with a nominal residual current
of 30 mA or less.
Position of the operator (see figure I)
Do not stand in line with the saw blade in front of the
u
power tool. Always stand to the side of the saw blade.
This protects your body against possible kickback.
– Keep hands, fingers and arms away from the rotating saw
blade.
1 609 92A 4SR | (27.02.2019)
– Do not reach one arm across the other when in front of
Mitre angle
45°
Switching on (see figure J)
85 x 85
– To start, press the on/off switch (17) and keep it
Note: For safety reasons, the on/off switch (17) cannot be
locked; it must remain pressed throughout operation.
85 x 85
The tool arm can only be guided downwards by pushing the
locking lever (1).
– Therefore, in order to saw, the locking lever (1) must be
85 x 85
Soft start
The electronic soft start limits the torque when the power
tool is switched on and increases the service life of the mo-
tor.
Switching off
– To switch off, release the on/off switch (17).
Sawing
– Firmly clamp the workpiece as appropriate for its dimen-
– Set the required mitre angle as necessary.
– Switch the power tool on.
– Push the locking lever (1) and slowly guide the tool arm
– Saw through the workpiece applying uniform feed.
– Switch off the power tool and wait until the saw blade has
– Slowly guide the tool arm upwards.
Checking and adjusting the basic settings
u
To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use.
Experience and suitable special tools are required for this.
A Bosch after-sales service point will handle this work
quickly and reliably.
Adjusting the laser
Note: To test the laser function, the power tool must be con-
nected to the power supply.
u
– Bring the power tool into the work position.
Checking: (see figure K1)
– Draw a straight cutting line on the workpiece.
– Push the locking lever (1) and slowly guide the tool arm
– Position the workpiece so that the teeth of the saw blade
the tool arm .
pressed.
pressed in addition to pulling the on/off switch.
sions.
downwards using the handle (16).
come to a complete stop.
Pull the plug out of the socket before carrying out any
work on the power tool.
While adjusting the laser (e.g. when moving the tool
arm), never activate the on/off switch. Accidental
starting of the power tool can lead to injuries.
downwards using the handle (16).
line up with the cutting line.
Bosch Power Tools
Advertisement
