Table of Contents
Advertisement
INSTRUCTIONS FOR SAFE HANDLING
1. Make sure that the tool is only connected to the voltage marked
on the name plate.
2. Never use the tool if its cover or any bolts are missing. If the
cover or bolts have been removed, replace them prior to use.
Maintain all parts in good working order.
3. Always secure the tool when working in elevated positions.
4. Never touch the blade, drill bit, grinding wheel or other moving
parts during use.
5. Never start the tool when its rotating component is in contact
with the work piece.
6. Never lay the tool down before its moving parts have come to a
complete stop.
7. ACCESSORIES :
The use of accessories or attachments other than those
recommended in this manual might present a hazard.
8. REPLACEMENT PARTS :
When servicing use only identical replacement parts.
CORDLESS DRIVER DRILL SAFETY PRECAUTIONS
1. Be aware that since this tool does not have to be plugged into
an electrical outlet, it is always in operating condition.
2. First, charge the battery.
3. Be sure the battery holder is securely snapped in place.
4. When not in use, lock the trigger.
5. When operating at high places, be aware of things below you.
6. Before drilling into walls, ceilings or floors, ensure that there are
no concealed power cables inside.
DISPOSAL OF THE EXHAUSTED BATTERY
Li-ion batteries must be recycled.
Take the battery to the shop from which it was purchased as soon
as the post-charging battery life becomes too short for practical use.
Do not discard the exhausted battery.
DESCRIPTION
1. Keyless chuck
2. Torque adjustment cap
3. Speed selector
4. Forward/ Reverse switch
5. LED work light
SPECIFICATIONS
Battery ..........................................................18V, 1,500mAh Li-ion
Chuck capacity ..................................................................... 10mm
No load speed .................................................. 0-400/ 0-1500min
Max torque ............................................................................ 20Nm
Drilling capacity ............................................................. steel: 8mm
Charger type..........................................................JLH08215037G
Clutch position ...................................................................... 21 + 1
Charging time ................................................................... 3-5hours
Net weight .............................................................................. 1.3kg
APPLICATIONS
(Use only for the purposes listed below.)
1. Drilling wood, ceramics, plastics, fiberglass, metal and concrete.
2. Driving and removing machine screws, wood screws, tapping
screws etc.
6. Trigger
7. Battery clip
8. Battery pack
9. Charging connector
wood: 19mm
KEYLESS CHUCK AND MOUNTING THE BIT (Fig. 1)
This tool comes equipped with a keyless chuck to easily mount
the bit.
Insert the bit into the chuck as far as it will go and rotate the chuck
clockwise to securely tighten the bit.
The bit can be removed by turning the chuck counterclockwise.
WARNING! Make sure to insert the drill bit straight into the chuck
jaws. Do not insert the drill bit into the chuck jaws at an angle then
tighten (Fig. 2). This could cause the drill bit to be thrown from the
drill, resulting in possible serious personal injury or damage to the
chuck.
TRIGGER (Fig. 3)
This tool is started and stopped by depressing and releasing the
trigger (6).
The drill speed is variable from 0 through 400 (Low speed position)
or from 0 through 1,500 (High speed position) by controlling the
trigger-squeezing force.
FORWARD/ REVERSE SWITCH (Fig. 3)
To change the direction of rotation, stop the tool by releasing the
trigger and push the forward/ reverse switch (4) to the opposite
side. When the reversing switch is set to the right position, the
direction of rotation will be clockwise when viewed from the handle
end of the drill. When the reversing switch is set to the left position,
the direction of rotation will be counter-clockwise.
The trigger can be locked by positioning the reversing switch at
the center. Lock the trigger whenever the tool is not in use.
LED WORK LIGHT (Fig. 3)
This tool is equipped with a LED work light (5) to illuminate the tip
of a bit. The light turns on by depressing the trigger.
SPEED SELECTION (Fig. 4)
To match the task at hand, two rotation speeds 1 (low) and 2 (high)
are featured. The speed can only be changed when the tool is at
rest. The speed selector(3) is located on top of the housing.
FASTENING TORQUE ADJUSTMENT (Fig. 4)
This tool is equipped with a clutch which enables the fastening
torque to be adjusted in 21 stages.
To use the tool in the screwdriver mode, set one of the numbers "1"
to "21" indicated on the torque adjustment cap (2) to the marked
(
) on the top side of housing. The higher number on the torque
adjustment cap, the greater the torque.
To use the tool in the drill mode, set the drill mark (
torque adjustment cap to the point. The clutch does not operate
when the tool is used in the drill mode.
CHARGING BATTERY PACK (Fig. 5, 6, 7, 8)
-1
The battery pack
(8)
condition to prevent possible problems. Therefore, you should
charge it prior to use.
NOTE: Batteries will not reach full charge the first time they are
charged. Allow several cycles for them to fully charge.
CAUTION!
Make sure power supply is normal house voltage, 230 volts, 50Hz,
AC only.
4
for the tool has been shipped in a low charge
) on the
Advertisement
Table of Contents
