Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Insta 418
Summary of Contents for Insta 418
- Page 1 MNL90418 Rev. H 02.27.19 MODEL 418 OPERATION AND MAINTENANCE MANUAL...
-
Page 2: Safety Summary
FOR USE BY QUALIFIED PERSONNEL ONLY Safety Summary Safety Summary International Symbols International Symbols WARNING In case of power cord damage, Power Off do not attempt to repair or replace the power cord. Contact the manufacturer or the local Power On distributor. - Page 3 This warranty does not apply to any machine that Your 418 series machine will have a long, trouble has been subjected to misuse, negligence or free life. Read this manual. Keep it with your accident.
-
Page 4: Installation
FOR USE BY QUALIFIED PERSONNEL ONLY Degree of Protection Installation DOMESTIC – 418 SERIES IP (Ingress Protection) rating according to IEC Use a separate 15 amp AC circuit. 60529. Only industrial extension cords with proper wire size should be used: size... -
Page 5: Operation
FOR USE BY QUALIFIED PERSONNEL ONLY Operation Environmental Conditions 1. Turn the power on by pressing the POWER Only operate Insta heat seal machines under button on the controller. suitable environmental conditions. 2. Set desired temperature and time. Open the 1. - Page 6 FOR USE BY QUALIFIED PERSONNEL ONLY Operation Timer/Temperature Temperature Control Fahrenheit/Centigrade (Celsius) Conversion The temperature controller can be programmed to display either °F or °C 1. Press the MODE button until the temperature is displayed. 2. Push and hold the UP and DOWN buttons for 5 seconds.
-
Page 7: General Maintenance
Rubber Pads from sparks, flame, or hot heat platen. 1. Make sure heat platen is cool. 5. The Model 418 machines require periodic lubrication with a high-temperature, non- 2. Use tube of MPPC006 adhesive to bond melting grease (MPPL023). - Page 8 Automatic Shut Off Automatic Shut Off Model 1. Turn on the machine by pressing POWER. (418 - Controller P/N MPC90214; Rev. 4.73) a) ONE beep indicates the Automatic Shut Off is OFF. b) TWO beeps indicates the Automatic Shut Off is ON.
- Page 9 FOR USE BY QUALIFIED PERSONNEL ONLY Safety and Danger Zone Diagram Hot Surface. Avoid contact with Upper Platen Shroud and Aluminum Casting Keep hands clear Do not handle the machinery with wet hands Machinery should be operated under a secure flat surface...
- Page 10 GREEN/YELLOW BLUE WHITE WHITE YELLOW GRAY PURPLE WHITE WHITE...
- Page 11 MODEL 418...
- Page 12 MODEL MODEL MODEL 418 EUR PART NAME 120V AC 230V AC 230V AC 418 BASE MPB90184 MPB90184 MPB90184 BASE UPRIGHT MPB90183 MPB90183 MPB90183 CLEVIS ASSY, GAS SPRING MPC90190 MPC90190 MPC90190 SCREW, BUTTON HEAD 1/4-20 x 5/8 MHSB142058 MHSB142058 MHSB142058 CARRIAGE BOLT 1/4-20 x 1.0...
- Page 13 FUSE (1 AMP, 250V) MPPF701R MPPF701R MPPF701R SCREW, PHILLIPS 2-56 X 1/4 MHSP25614 MHSP25614 MHSP25614 MARKER STRIP MS6992 MS6992 MS6992 SCREW, PAN HD 6-32 X 1/4 MHSP63214 MHSP63214 MHSP63214 SCREW, SOCKET HEAD 1/4-20 X 5/8 MHSSH142058 MHSSH142058 MHSSH142058 WASHER #1/2 MHWSAE12 MHWSAE12 MHWSAE12...
- Page 14 What Insta will ask you to do? After contacting Insta you may be asked to deliver (by hand if you prefer) or send The Product properly packaged, freight prepaid, to Insta or Insta’s service center together with your bill of...
- Page 15 This Limited Warranty (and Insta’s obligation to you) may not be changed in any way unless you and Insta sign the same piece of paper in which we (1) refer to The Product and your bill of sale date, (2) describe the change to this warranty and (3) agree to make that change.
- Page 16 13925 E. 166 St. ● Cerritos, CA USA 90702 ● (800) 421-6971 ● Fax (562) 404-3010 Parts Orders ● (800) 426-3609 ● (562) 404-3000 Ext. 215 Technical Support ● (800) 426-3609 ● (562) 404-3000 Ext. 351 In-House Repair ● (800) 426-3609...
Need help?
Do you have a question about the 418 and is the answer not in the manual?
Questions and answers