Download Print this page

Whirlpool WFW3090G Manual

Advertisement

Quick Links

Location Requirements

Proper installation is your responsibility.
You will need:
n A grounded electrical outlet located within 5.4 ft (1.7 m)
of power cord on back of washer.
n Water faucet located within 4 ft (1.2 m) of water fill valve on washer,
and water pressure of 20–100 psi (137.9–689.6 kPa).
n A level floor with maximum slope of 1" (25 mm) under entire washer.
Installing on carpet or surfaces with foam backing is
not recommended.
n Floor must support washer's total weight (with water and load) of 400
lbs (180 kgs).
IMPORTANT: Do not install, store, or operate washer where it will be
exposed to weather or in temperatures below 32°F (0°C). Water remaining
in washer after use may cause damage in
low temperatures. See "Washer Maintenance" for winterizing information.
33
33
/
" Min.
" Min.
1
1
4
2
(845 mm)
(851 mm)
33
" Max.
3
33
4
" Max.
/
3
4
(857 mm)
(857 mm)
24"
(610 mm)
* 2.3 cu. ft. models: 42
1.9 cu. ft. models: 41
2.3 cu. ft. models: 25
1.9 cu. ft. models: 24" (610 mm)
All dimensions show recommended spacing allowed, except for closet
door ventilation openings which are the minimum required.
For each arrangement, consider allowing more space for ease of installa-
tion and servicing, and spacing for companion appliances and clearances
for walls, doors, and floor moldings.
24"
(610 mm)
*
41
/
"
1
2
(1054 mm)
/
"
3
4
⁄16" (1091 mm)
15
(18 mm)
⁄8" (1057 mm)
5
⁄8" (638 mm)
1
Washer
PRODUCT MODEL NUMBERS
WFW3090G, WFW5090G
Space must be large enough to allow door to fully open.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or louvered door is installed,
top and bottom air openings in door are required.
Recessed area or closet installation
(stacked washer and dryer):
4"*
0"/1"
(102 mm)
(0 mm/25 mm)
0"/1"
1"*
(0 mm/25 mm)
(25 mm)
External exhaust elbow requires additional space.
Custom under counter installation:
1"
(25 mm)
Custom cabinet installation:
7"
(178 mm)
*
4"
(102 mm)
(25 mm)
0"/1"
(0 mm/25 mm)
3"
(76 mm)
68
" Min.
3
4
(1746 mm)
65
"
/
3
4
(1670 mm)
69
" Max.
1
2
(1765 mm)
3"
(76 mm)
0"/1"
* Recommended
1"*
(0 mm/25 mm)
(25 mm)
spacing. Minimum
0" (0 mm)
39" min.
(990 mm)
1"
(25 mm)
3"
(76 mm)
1"
9"
9"
(229 mm)
(229 mm)
(25 mm)
3"
(76 mm)
* Recommended
spacing. Minimum
*
*
1"
1"
0" (0 mm)
(25 mm)
48 in.
2
(310 cm
)
2
24 in.
2
(155 cm
)
2
48 in.
min.
2
(310 cm
)
2
24 in.
min.
2
(155 cm
)
2
W10856086B
1/2017

Advertisement

loading

Summary of Contents for Whirlpool WFW3090G

  • Page 1: Location Requirements

    Washer PRODUCT MODEL NUMBERS WFW3090G, WFW5090G Location Requirements Space must be large enough to allow door to fully open. Add spacing of 1" (25 mm) on all sides of washer to reduce Proper installation is your responsibility. noise transfer. If a closet door or louvered door is installed, You will need: top and bottom air openings in door are required.
  • Page 2: Electrical Requirements

    (114 mm) See requirements for floor standpipe drain system. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice.

This manual is also suitable for:

Wfw5090g