Related Manuals for Sarstedt LC 6
Summary of Contents for Sarstedt LC 6
- Page 1 Operating Instruction Centrifuge LC 6 Instruction Manual Centrifuge LC 6 with horizontal rotor 6 x SARSTEDT-No.: 90.184.500 V. 2.1.2 / 01.2009...
-
Page 2: Table Of Contents
Operating Instruction Centrifuge LC 6 Table of contents Page E- 1. Device data ........................3 2. Manufacturer's address ...................... 3 3. Important notes........................3 Explanation of symbols.........................4 Device-specific safety notes ......................4 Responsibilities of the owner......................5 Responsibilities of operating personnel ..................5 4. -
Page 3: Device Data
Please keep these instructions in a safe place for future reference. Copyright The copyright for these operating instructions lies with SARSTEDT-AG & Co. The instructions are only intended for use by operating personnel and for the purchaser of the device. -
Page 4: Explanation Of Symbols
Operating Instruction Centrifuge LC 6 Explanation of symbols These operating instructions contain important symbols to indicate dangers and possible operating errors. The ”Caution“ symbol means that in this section: • Important information is given. • An immediate or possible risk of danger to life and limb of persons is described. -
Page 5: Responsibilities Of The Owner
Operating Instruction Centrifuge LC 6 During the warranty period, the device may only be repaired by SARSTEDT AG & Co. or by persons authorized by SARSTEDT AG & Co. In case of improper use or repair, the warranty will be void. -
Page 6: Other Information
In addition to the lid safety switch, the LC 6 is equipped with a “0 rpm” lid locking system. This safety system keeps the lid closed at all times (even in the event of a power failure) and ensures that the lid can be unlocked only when the rotor has come to a standstill. -
Page 7: Transport, Installation And Connection
(recommended for glass and flat bottom tubes) 92.184.553 1.0 inch rubber adapter (recommended for glass and flat bottom tubes) If you have any questions concerning other SARSTEDT products or the SARSTEDT product range, please contact: SARSTEDT AG & Co. Postfach 1220 D-51582 Nümbrecht... -
Page 8: Technical Data
Operating Instruction Centrifuge LC 6 Technical Data Machine data: Apparatus: Centrifuge LC 6 Rotor: horizontal rotor 6 x Tube holder: 6 pieces Order number: SARSTEDT No. 90.184.500 Centrifuge motor: HP brushless induction motor Kinetic energy: < 200 Nm Timer: electronic,... -
Page 9: Rotor Removal And Installation
Operating Instruction Centrifuge LC 6 Rotor Removal and Installation • Open the lid lock using the “OPEN/(EMERGENCY STOP)“ button. • Pull out the mains plug. • Remove the tube holder. • Losen and remove the rotor nut in the centre... -
Page 10: Operation
Operating Instruction Centrifuge LC 6 • Apparatus accelerates, tube holders slip into a horizontal position. • Pay attention to the running noise of the centrifuge. There should be a soft humming. In the case of loud or unusual noise stop centrifuge immediately by pushing the “OPEN/(EMERGENCY STOP)“... -
Page 11: Counter
Operating Instruction Centrifuge LC 6 Press the “OPEN/(EMERGENCY STOP)“ button 3 times until all display lights have stopped flashing and are off, to confirm the set time. Recommended conditions for centrifugation of S-Monovettes with gel preparation: Ø Tube holder 100 mm Ø... -
Page 12: Maintenance And Servicing Service Address
Service address Should you have questions or problems concerning the device, please contact the customer service department of DESAGA GmbH / SARSTEDT-GRUPPE in Wiesloch or your local SARSTEDT sales office. Remember to specify the Serial no. of the device. DESAGA GmbH / SARSTEDT-GRUPPE... -
Page 13: Cleaning
Operating Instruction Centrifuge LC 6 Cleaning Potential danger of contamination The regulations for cleaning the device must be observed. Inattentive cleaning or non-observance of the regulations can cause malfunctions! • Disconnect the device from the mains supply before cleaning. •... -
Page 14: Contamination Questionnaire
Contamination questionnaire for repair orders Dear Customer, Please complete the contamination questionnaire before you return the instrument to the service department of DESAGA GmbH / SARSTEDT-GRUPPE or to your local SARSTEDT sales representative for maintenance or repair. Firm: Department: Town:...
Need help?
Do you have a question about the LC 6 and is the answer not in the manual?
Questions and answers