Kenwood TK-U100V Service Manual page 8

TK-U100
4. Clone Mode
Programming data can be transferred from one transceiv-
er to another by connecting them via their SP/MIC connec-
tors.
Cloning can be performed as described below (the trans-
mit transceiver is the source and the receive transceiver is
the target).
The following data cannot be cloned.
• Tuning data
• Model name data
• ESN data
1. Turn the source transceiver and target transceiver power
OFF.
2. Turn the source transceiver power ON while pressing the
[PTT] and [Side] keys, to enter clone mode.
3. Connect the cloning cable (part No. E30-3410-05) to the
SP/MIC connectors on the source and target transceivers.
4. Turn the target transceiver power ON.
5. Press the [Side] key on the source transceiver.
The data of the source is sent to the target. While the
source is sending data, red LED will light. While the target
is receiving the data, green LED will light. When cloning
of data is completed, the source red LED turned off, and
the target automatically operates in the User mode.
6. Additional targets can be continuously cloned. When the
[Side] key on the source is pressed, the data of source is
sent to the target again. Repeat steps 3 to 5 to clone ad-
ditional transceivers.
Note:
• The Model name and Market codes must be the same in
order to clone the transceiver.
• If the transceivers clone mode is confi gured as "Disabled",
the transceiver cannot enter clone mode.
• If the Read authorization password is set to the transceiv-
er, the transciever cannot enter to the clone mode.
• Cannot be cloned if the password (overwrite password) is
programmed to the target.
8
V
( )
REALIGNMENT /
模式组合
4. 复制模式
用 SP/MIC 连接器连接手持对讲机，可以将编程数据从一台
手持对讲机传输到另一台手持对讲机。
如下所述可进行复制（发射手持对讲机为主机，接收手持
对讲机为子机） 。
以下数据不能复制。
·调谐数据
·机型数据
·ESN 数据
1. 关闭主机和子机的电源。
2. 按 [ P T T ] 和 [ 侧面 ] 键的同时打开主机的电源，使其进入
复制模式。
3. 将复制电缆（零件号 E30-3410-05）连接到主、子机的 SP/
MIC 连接器上。
4. 打开子机的电源。
5. 按主机上的 [ 侧面 ] 键。
主机的数据便被发送到子机。主机发送数据时，红色 L E D
将呈。子机接收数据时，绿色 L E D 呈。数据复制完成后，
主机的红色 LED 熄灭，子机自动以用户模式运行。
6. 可以继续复制其他子机。按主机上的 [ 侧面 ] 键，主机的
数据再次被发送到子机。重复步骤 3 ～ 5 复制其他手持对
讲机。
注意 ：
· 机型和市场代码必须相同才能复制手持对讲机。
• 如果手持对讲机复制模式被设置为"无效" ，则手持对讲机
不能进入复制模式。
• 如果手持对讲机设置了读取授权密码，则手持对讲机无法
进入复制模式。
• 如果子机编程设有密码 ( 改写密码） ，则无法复制。
Cloning cable
复制电缆
(E30-3410-05)