Kenwood TK-U100V Service Manual page 6

TK-U100
2. When the POWER is switched on, user mode can be en-
tered immediately. When the PC sends a command, the
transceiver enters PC mode.
When data is read from the transceiver, the red LED
lights.
When data is written to by the transceiver, the green LED
lights.
Note:
• The data stored in the personal computer must match
Model Name and Model Type when it is written into EE-
PROM.
• Do not press the [PTT] key during data transmission or
reception.
3-3. KPG-22/KPG-22A Description
(PC programming interface cable: Option)
The KPG-22/22A is required to interface the transceiver
with the computer. It has a circuit in its D-sub connector
(KPG-22: 25-pin, KPG-22A: 9-pin) case that converts the RS-
232C logic level to the TTL level.
The KPG-22/22A connects the SP/MIC connector of the
transceiver to the RS-232C serial port of the computer.
3-4. KCT-53U Description (USB adapter: Option)
The KCT-53U is a cable which connects the KPG-22A to a
USB port on a computer.
When using the KCT-53U, install the supplied CD-ROM
(with driver software) in the computer. The KCT-53U driver
runs under Windows 2000, XP or Vista (32-bit).
3-5. FPU (Programming Software) Description
The FPU is the programming software for the transceiver
supplied on a CD-ROM. This software runs under windows
XP, Vista or 7 on a PC. The software on this disk allows a
user to program the transceiver via Programming interface
cable (KPG-22/22A).
Note:
Use the FPU that matches the market when you fi rst set
the market code and model name/frequency data to the
service unit. The unit set by mistake cannot be restored.
Receive frequencies listed below may result in the inter-
ference of reception due to the harmonics of internal oscilla-
tors.
Enter a frequency not listed in the table.
No. Frequency (MHz)
1 152.69375
2 152.69500
3 152.70000
4 152.70500
5 152.70625
6 153.59375
7 153.59500
8 153.60000
6
V
( )
REALIGNMENT /
No. Frequency (MHz)
9 153.60500
10 153.60625
11 172.79375
12 172.79500
13 172.80000
14 172.80500
15 172.80625
模式组合
2. 手持对讲机电源打开时，可以立即进入用户模式。P C 发送
指令时，手持对讲机进入 PC 模式。
手持对讲机发送数据时，红色的 LED 点亮。
手持对讲机接收数据时，绿色的 LED 点亮。
注意 ：
• 个人电脑保存的数据写入 EEPROM 时，必须与机型和类型相
符。
• 请勿在数据发送或接收期间按 [PTT] 键。
3-3. KPG-22/KPG-22A 说明
(PC 编程接口电缆 ： 选购件 )
将 手 持 对 讲 机 与 电 脑 相 连 需 要 K P G -22/22A。 该 电 缆 的
D-sub 连接器 (KPG-22 ： 25 针，KPG-22A ： 9 针 ) 盒具有将 RS-
232C 逻辑电平转换为 TTL 电平的电路。
K P G -22/22A 将手持对讲机的 S P / M I C 连接器连接到电脑的
RS-232C 串行端口。
3-4. KCT-53U 说明 (USB 适配器 ： 选购件 )
KCT-53U 是将 KPG-22A 连接到电脑 USB 端口的电缆。
使用 K C T -53U 时，请在电脑上安装附带的 C D - R O M ( 带有
驱动程序软件 )。K C T -53U 驱动程序在 W i n d o w s 2000, X P 或
Vista(32 位 ) 下运行。
3-5. FPU( 编程软件 ) 说明
FPU 是 CD-ROM 附带的用于手持对讲机的编程软件。该软件
在 PC 的 Windows XP、Vista 或 7 下运行。该光盘上的软件允
许用户通过编程接口电缆 (KPG-22/22A) 对手持对讲机进行编
程。
注意 ：
初次设置服务单元的市场代码和机型 / 频率数据时，请使
用与市场相符的 FPU。若单元设置有误，将无法予以恢复。
下面列出的接收频率由于内部振荡器的谐波可能对信号接
收造成干扰。
输入在表格中没有列出的频率
编号 频率 (MHz)
1 152.69375
2 152.69500
3 152.70000
4 152.70500
5 152.70625
6 153.59375
7 153.59500
8 153.60000
编号 频率 (MHz)
9 153.60500
10 153.60625
11 172.79375
12 172.79500
13 172.80000
14 172.80500
15 172.80625