Speaker Connection; Headphone Output 4; Remote Sensor 5; Display 6 - Rotel RA-630 Owner's Manual

Speaker Connection

Turn off all the components in the system before connecting the speakers.
The amplifier has color-coded binding post type speaker connectors on the
back panel. These connectors accept bare wire, connector lugs, or dual
banana type connectors. (except in European Community countries where
their use is not permitted)
Route the wire from the amplifier to the speakers. Give yourself enough slack
so you can move the components to allow access to the speaker connectors.
If you are using dual banana plugs, connect them to the wires and then
plug into the backs of the binding posts. The thumbscrews of the binding
posts should be screwed in all the way (clockwise).
If you are using terminal lugs, connect them to the wires. If you are attaching
bare wires directly to the binding posts, separate the wire conductors and
strip the insulation from the end of each conductor. Be careful not to cut
into the wire strands. Unscrew (turn counterclockwise) the binding post
thumbscrews. Place the connector lug or wire around the binding post
shaft. Turn the thumbscrews clockwise to clamp the connector lug or wire
firmly in place.
NOTE: Be sure there are no loose wire strands that could touch adjacent
wires or connectors.

Headphone Output 4

The headphone output allows you to connect headphones for private listening.
This output accepts a standard 3.5mm (1/8") mini stereo headphone
connector. Plugging in a set of headphones will cut off the signal to the
speaker outputs. The settings of the Function Selector determines which
source is heard.
NOTE: Because the sensitivity of speakers and headphones can
vary widely, always reduce the volume level before connecting or
disconnecting headphones.

Remote Sensor 5

This remote sensor window receives IR commands from the remote control.
Please do not block this sensor.

Display 6

The front panel display shows the source selected, volume level and tone
settings.

Front USB Input 9

The front USB input can be connected to an iPod, iPhone, USB flash memory
or the Bluetooth dongle (supplied) for wireless streaming. With iPod or
iPhones, simply plug the device into the front USB and select USB function
from the source selector. The iPod and iPhone remain active allowing search
and play functions.

Bluetooth Dongle

Insert the supplied Bluetooth Dongle into the front USB of the RA-630 for
wireless streaming via Bluetooth, from your device (i.e. mobile phones).
From your mobile device, look for "Rotel Bluetooth" and connect to it.
Connection is normally automatic, but if prompted for a password, please
press "0000" then enter on your device.
NOTE: Not all Bluetooth dongles will operate with RA-630. Please
use the one supplied.

Audio Controls

Volume Control 8 B

Turn the controls clockwise to increase the volume, or counter clockwise to
decrease the volume. From the remote control press the volume + or - button
to turn the volume up or down. Press the MUTE
mute the volume.

Balance Control 7 C

The Balance Control adjusts the left-to-right balance of the sound output.
The factory default is the center position or "0". To change the balance
from the front panel, press the MENU
to BALANCE SETTING mode. Then press the left/right arrow button on the
front panel to change the value to LEFT or RIGHT. The value can change
from L15 to R15.
NOTE: This setting is saved permanently including after powering off
the RA-630.
To make temporary changes not saved after power off, from the remote,
press the BAL button to access the BALANCE SETTING menu, then
C
press the left/right arrow button to adjust. When finished, press the EXIT
button to exit the menu.
G

Tone Control Bypass 7 F

Bass and Treble Control (Tone Control) circuits are bypassed at factory
default to ensure the purest possible sound. The front display will show
TONE BYPASS. To turn on the tone control from the front panel, press the
MENU 7 button to toggle to the Bypass control then press the left/right
arrow button to turn bypass on or off.
NOTE: This setting is saved permanently including after powering off
the RA-630.
To temporarily changes the Tone Control Bypass, press the BYPASS
on the remote control to toggle the Bypass mode enabled and disabled.

Bass and Treble Controls 7 C

Set the Bass or Treble controls from the front panel by pressing the MENU
7 button to toggle to either the Bass or Treble Setting menu. Then press
the left/right arrow button to adjust the value. The Bass and Treble values
range from -10 to +10.
NOTE: These settings are saved permanently including after powering
off the RA-630.
To temporarily change the Bass and Treble settings from the remote control,
press the Bass or Treble button , then press the left/right arrow button
C
on the remote to adjust the value.
button to completely
B
7 button to toggle the front display
button
F
11