Table of Contents
Advertisement
Quick Links
PROCRAFT
WELDING
INVERTER PLAMA CUTTER
511468
OPERATING INSTRUCTIONS
SAVE THIS MANUAL
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
Keep this manual for the safety warnings and precautions,
assembly, operating, inspection, maintenance and
cleaning procedures. Write the product's serial number
in the back of the manual (or month and year of purchase
if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference.
Advertisement
Table of Contents
Related Manuals for PROCRAFT 511468
Summary of Contents for PROCRAFT 511468
-
Page 1: Operating Instructions
PROCRAFT WELDING INVERTER PLAMA CUTTER 511468 OPERATING INSTRUCTIONS SAVE THIS MANUAL WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. -
Page 2: Electrical Safety
SAVE THIS MANUAL ELECTRICAL SAFETY Keep this manual for the safety warnings and precautions, 1. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back ordinances. -
Page 3: Personal Safety
PERSONAL SAFETY SERVICE 1. Stay alert. Watch what you are doing, and use common 1. Tool service must be performed only by qualified sense when operating a power tool. Do not use a power repair personnel. Service or maintenance performed by tool while tired or under the influence of drugs, alcohol, unqualified personnel could result in a risk of injury. - Page 4 a. When possible, move the work to a location well away Use natural or forced air ventilation and wear a respirator from combustible; protect the combustibles with a cover approved by NIOSH to protect against the fumes produced made of fire resistant material. to reduce the risk of developing the above illnesses.
-
Page 5: Specifications
SPECIFICATIONS MODEL 511468 POWER VOLTAGE (V) 1PH ~ 220V+15% FREQUENCY (HZ) ( 50/60HZ) RATED INPUT CURRENT (A) NO-LOAD VOLTAGE 19.8 OUTPUT CURRENT (A) 15-40 DUTY CYCLE (%) 100% @ 30A 60-80PSI@4-6kg/cm2 STEEL PLATE 12mm ALUMINUM PLATE EFFICIENCY PROTECTION CLASS IP 21S... -
Page 6: Operation
7. Verify that the Power Switch is in the Off (O) position, then plug the 240V~line cord plug into an appropriate Grounding the tool: 240V~outlet for 511468. Attach a ground wire of at least 14 Ga. thicknesses (not 8. Turn the Power Supply Controller to the desired current supplied) to the screw on the lower left of the back of (15 to 40 amps). -
Page 7: Plasma Cutting Technique
PLASMA CUTTING TECHNIQUE How do Plasma Cutters Work? Using a plasma cutter is a skill that requires time and effort Plasma cutters work by sending a pressurized gas through to do well. Practice striking and maintaining an arc on a small channel. In the centre of this channel, there is a scrap work pieces before beginning work. - Page 8 a. Abnormal vibration, sound or smell. AIR PRESSURE CORRECT b. Abnormal heating at any cable connection. Check that the grounding point and the metal being cut are clean, dry, and free from all coatings and paint. These c. Then fan does not work properly. sections need to be able to conduct electricity efficiently d.
- Page 9 AIR PRESSURE TOO LOW GUARANTEE PROCRAFT WARRANTY INFORMATION a. Verify that the compressor is delivering at least Every PROCRAFT welder has been thoroughly inspected 6 CFM @60 PSI to the tool. and tested before leaving the factory. In addition to any statutory regulations, TOOLEX warrants all of its products b.
- Page 10 511468 Front Unit 511468 Back Unit Main Power Light Power Switch Amperage Control Over Temperature Light Torch Torch Switch Output Air Pressure Connection Input Power Connection Terminal Hose Cable Page 10...
- Page 11 INCLUDED STANDARD ACCESSORIES 511468: 40i PLASMA CUTTER INCLUDED STANDARD ACCESSORIES Plasma Cutting Torch Earth Clamp (500889) (500892) Page 11...