Table of Contents
Advertisement
Quick Links
PROCRAFT
WELDING
MMA / TIG
MODELS 511464, 511465 & 511466
OPERATING INSTRUCTIONS
SAVE THIS MANUAL
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below may result
in electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
Keep this manual for the safety warnings and precautions,
assembly, operating, inspection, maintenance and
cleaning procedures. Write the product's serial number
in the back of the manual (or month and year of purchase
if product has no number). Keep this manual and the
receipt in a safe and dry place for future reference.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PROCRAFT 511464
Summary of Contents for PROCRAFT 511464
- Page 1 PROCRAFT WELDING MMA / TIG MODELS 511464, 511465 & 511466 OPERATING INSTRUCTIONS SAVE THIS MANUAL WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE THESE INSTRUCTIONS...
-
Page 2: Important Safety Information
IMPORTANT SAFETY INFORMATION 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an In this manual, on the labeling, and all other information increased risk of electric shock if your body is grounded. provided with this product: 4. -
Page 3: Specific Safety Rules
1. Do not use the power tool if the Power Switch does not a. Wear the approved safety impact eye goggles with a turn it on or off. Any tool that cannot be controlled with welding helmet featuring at least a number 10 shade lens the Power Switch is dangerous and must be replaced. -
Page 4: Toxic Fumes
WARNING 1. Proper cylinder care. Secure cylinders to a cart, wall, or post, to prevent them from falling. All cylinders should be INHALATION HAZARD: Welding and Plasma used and stored in an upright position. Never drop or strike Cutting Produce a cylinder. - Page 5 About the machine MMA series welding machine is a rectifier adopting the most advanced inverter technology. The development of inverter gas-shielded welding equipment profits from the development of the inverter power supply theory and components. Inverter gas-shielded welding power source utilizes high-power component IGBT to transfer 50/60HZ frequency up to 50KHZ, then reduce the voltage and commutate, and output high-power voltage via PWM technology.
- Page 6 MODELS 511464 511466 511465 140AMP 180AMP 200AMP Parameters 240V 240V 240V Power Voltage (V) Frequency (hz) 50/60 50/60 50/60 Rated Input 22.1 Current (A) Output Current 20 - 200 20 - 140 20 - 180 Rated Input 24.4 Voltage (V)
- Page 7 equipment. When power voltage moves between± 15% of rated voltage, it still can work normally. When use long cable, in order to prevent voltage form going down, bigger section cable is suggested. If cable is too long, it may affect the performance of the power system.
- Page 8 511464 511465 Panel Instruction: Panel Instruction: MODEL: 511465 INVERTER MMA / TIG 220i 511466 Panel Instruction: Page 8...
-
Page 9: Duty Cycle
DUTY CYCLE OPERATION Duty Cycle is the equipment specifications which defines the Note: Before beginning, please read and understand all number of minutes within a 10 minute period that a piece of the safety precautions staring on page 1 and especially the equipment can safely operate. - Page 10 MAINTENANCE WARNING! Make sure the Power Switch of the WELDER is in it’s “OFF” position and that the tool is unplugged from the electrical outlet before performing any inspection, maintenance, or cleaning procedures. 1. Before each use, inspect the general condition of the Welder. Check for loose cable connections, misalignment or binding of the fan, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation.
- Page 11 MANUAL METAL ARC (MMA) WELDING Shielded metal arc welding (SMAW), also known as manual metal arc (MMA) welding, and flux-shielded arc welding or informally as stick welding, is a manual arc welding process that uses a consumable electrode coated in flux to lay the weld.
- Page 12 PROCRAFT WARRANTY INFORMATION Every PROCRAFT welder has been thoroughly inspected and tested before leaving the factory. In addition to any statu- tory regulations, TOOLEX warrants all of its products against faulty workmanship and faulty material for a twelve (12)
- Page 13 INCLUDED STANDARD ACCESSORIES 511464: 140i MMA / TIG INCLUDED STANDARD ACCESSORIES 4m Cable & Electrode 4m Cable & Holder (500890) Earth Clamp (500892) 511465: 220i MMA / TIG INCLUDED STANDARD ACCESSORIES 4m Cable & 4m Cable & Earth Clamp Electrode Holder...
Need help?
Do you have a question about the 511464 and is the answer not in the manual?
Questions and answers