Related Manuals for ALW LIGHTPLANE 2
Summary of Contents for ALW LIGHTPLANE 2
- Page 1 INSTALLATION INSTRUCTIONS LIGHTPLANE 2 LP2 | Suspended | LED 1035 22nd Avenue, Unit 1 Oakland, CA 94606 510.489.2530 TalkToUs@alwusa.com alwusa.com...
- Page 2 Safety & Warnings! 1. Read all instructions. 2. Install in accordance with national and local electrical code regulations. 3. This product is intended to be installed and serviced by a qualified, licensed electrician. 4. Turn off electrical power before installing or servicing fixture in any way. 5.
-
Page 3: Table Of Contents
Table of Contents Luminaire Overview Diagrams Components Parts (by others) Tools Required Quick Specs Installation Prepare Ceiling Standard Suspension Connecting Multiple Sections Troubleshooting Wiring Diagrams LP2 Suspended Installation Guide 3 of 12 102-000026 - IG121818-A.0... -
Page 4: Luminaire Overview
LUMINAIRE OVERVIEW To Building Power Ceiling Fitting / Suspension Bullet J-Box Canopy Power Cord Suspension Cables Cable Gripper Fixture Body Integrated LED Driver STANDARD SUSPENSION COMPONENTS Suspension Cable Canopy Assembly Suspension Bullet Ceiling Fitting Quick Specs Parts (by others) Tools Required Input Voltage / Frequency: Junction Box (Optional) Drill... -
Page 5: Installation
Installation: Prepare Ceiling Installation: Standard Suspension See Final/Record Drawings for Mounting Locations Install Ceiling Fitting - Framing ELECTRICAL WIRING: See final/record drawings for mounting locations. Install Ceiling Fittings may be installed directly into framing with framing or strut channels with consideration for alignment appropriate hardware. - Page 6 Installation: Standard Suspension (Cont.) Route Suspension Cable and Attach to Ceiling Raise Fixture to Suspension Cables Route Suspension Cable through Suspension Bullet. Ball Raise fixture to Suspension Cables, and attach fixture by end should sit in Suspension Bullet. Screw Suspension Bullet inserting Suspension Cable through Cable Grippers.
-
Page 7: Connecting Multiple Sections
Installation: Standard Suspension Installation: Connecting Multiple (Cont.) Sections DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while installing canopy. Mount Canopy Bracket to J-Box & Secure Canopy Remove Lens Mount Canopy Bracket to J-Box using provided screws, Carefully remove lens using suction cup or similar. CAUTION: then secure Canopy over J-Box with finial. - Page 8 Installation: Connecting Multiple Sections (Cont.) Align and Join Sections Together Tighten Set Screws on Outer Corner Loosen set screws and slide out joiner bracket halfway Tighten set screws to secure outer corner bracket to to allow for joining. Join sections together, as shown, joined section using a 1/8”...
- Page 9 Installation: Connecting Multiple Sections (Cont.) SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installation or servicing. DO NOT PINCH OR PUT EXCESSIVE TENSION ON WIRES while joining sections or reattaching heatsink. Install Diffuser Shim Install Diffuser Shim at each joined location to prevent light leak between lens sections.
-
Page 10: Troubleshooting
Troubleshooting Only a certified electrician can service and troubleshoot product field issues. Always turn main power off before servicing fixture. Full Fixture does not illuminate • Ensure all wire connections are made. • Ensure fixture is wired correctly and power is on. •... -
Page 11: Wiring Diagrams
Wiring Diagrams Canopy/Power Feed Traditional On/Off Black Line Voltage (Hot) White Line Voltage (Neutral) AC 50/60Hz Green Ground Canopy/Power Feed 0-10V Dimming Black Line Voltage (Hot) White Line Voltage (Neutral) AC 50/60Hz Green Ground Grey DIM- 0-10VDC (Dim-) Purple DIM+ 0-10VDC (Dim+) Canopy/Power Feed Black... - Page 12 Wiring Diagrams (Cont.) Canopy/Power Feed DALI Black Line Voltage (Hot) White Line Voltage (Neutral) AC 50/60Hz Green Ground Purple Data + DATA + Grey Data - DATA - Canopy/Power Feed Lutron LDE Black Line Voltage (Hot) White Line Voltage (Neutral) AC 50/60Hz Green Ground...
Need help?
Do you have a question about the LIGHTPLANE 2 and is the answer not in the manual?
Questions and answers