Table of Contents
Advertisement
7. Exit the scan mode by pressing "S". Your radio will re-
turn to normal operation.
NOTE: If your scan list is empty/unprogrammed, the
"S" will not illuminate, scan will not start and an alert
tone will sound.
Priority Scan
1. With microphone on-hook, press the "S" and "P".
Each will illuminate and the radio will be in the priority
scan mode.
2. The scanner stops on the first scan channel with activ-
ity. If that channel is not a priority channel, the scanner
will continue to monitor both priority channels every
Look Back Time.
3. When the transceiver finds the #2 Priority Channel
with activity, it decodes that channel activity while con-
tinuing to monitor Priority Channel #1. However, if ac-
tivity is found on Priority Channel 1, the scanner will
remain there until carrier drops and the Scan Wait Time
is over.
4. Going off-hook at any time during Priority Scan will
result in the radio and the display reverting to the #1 pri-
ority Channel. Transmitting will then occur on Priority
#1.
5. Returning microphone to its holder will cause the Pri-
ority Scan sequence to restart.
6. Exit the Priority Scan mode by pressing both the "S"
and "P" (to extinguish). Radio and display will return to
priority #1 channel for normal operation.
Limited Priority Scan
1. With microphone on-hook, press the "P". It will light
and your transceiver will start to scan for activity on the
#1 and #2 Priority Channels as will as the channel you
assigned Limited Priority Scan.
2. As in priority Scan, the transceiver will monitor the
priority channels every Look Back Time as programmed
by the dealer.
3. Operating remains the same as in Priority Scan
4. Exit the Limited Priority Scan by pressing the "P". Ra-
dio and display will remain on the non-priority channel
for normal operation.
Vacant Channel Scan
1. With the microphone off-hook, press the "S" and the
radio will start scanning for a vacant channel on which
to transmit.
2. The "S" will blink to indicate that vacant channel scan
is in process.
3. The radio will lock onto the first channel with no ac-
tivity. If that channel becomes active during the scan
wait time, the vacant channel scan will then resume.
4. If you press the PTT to transmit, the "S" will go out,
the TX LED will go on, and you will have exited the va-
cant channel scan mode. Otherwise, simply return the
microphone to its holder.
FRONT PANEL PROGRAMMING
To enter the user programming mode, press and hold the
"P" during the initial 4 seconds at radio turn-on. The ra-
dio will sound the prompt tone and display the message
"Prog".
Scan List Programming
1. After entering the programming mode, press the "S",
the radio will display channel "01". The number will
blink if channel one is not in the list.
2. Then insert this or any channel onto the scan list,
press the "S" while the channel number is flashing in the
display. The channel number will be displayed continu-
ously to indicate that it is stored in the scan list.
3. You can now use the channel up and down buttons to
change the displayed channel number accordingly.
4. To delete a channel from the scan list, press the 1 but-
ton/LED. The display will change from continuous to
flashing, indicating that the deletion was successful.
5. After you have completed programming your scan
list, press the "P". The radio will sound the prompt tone
and display the message "Prog".
6. Press the "P" again to save the scan list in the micro-
processor's memory.
7. Press the "2" to exit the user programming mode.
NOTE: Use the "1" to delete displayed channel from the
scan list; use the "S" to store displayed channel in the
scan list.
Priority Channel Programming
1. After you have entered the user programming mode,
press the "P" to change the display to indicate the cur-
rent #1 priority channel.
2. Use the Channel up and down buttons to change it.
3. After you have selected the First Priority Channel,
press the "S" to save it and to bring up Priority Channel
2 in the display.
4. Use the Channel up and down buttons to get to the de-
sired priority #2 channel.
5. After you have selected Second Priority Channel,
press the "P" to save the priority channel programmed,
to sound the prompt tone and to display the message
"Prog".
6. To exit from priority channel programming mode,
press the "2".
Advertisement
Table of Contents
