Advertisement
Quick Links
Chrysler/Dodge/Jeep Remote Add-On CD player
2013-current RAM truck and Viper; 2015-current Charger,
Please read thoroughly before starting installation and check that kit contents are complete.
Items Included in the Kit:
T-harness
OEM Remote CD player
Universal case and bracket mounts
4 self-drilling screws for mounting to metal, 4
stingers for plastic
2 stand-off threaded spacers
(for Pacifica installs)
Remote CD player harness
5000-8750 module to enable CD player
Templates
These instructions
Safety Precautions:
• Work in well ventilated area that is clear of obstructions.
• Secure vehicle with tire chucks in both front and rear of tires.
• Turn vehicle accessories OFF and ensure ignition key is in OFF position.
• Wear safety goggles and snug fitting clothes.
• Use tools only for their intended purpose and which are in good repair.
• Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color
instructions, as well as an installation video, please visit www.brandmotion.com
5000-8750 Instructions 02-22-17.docx
for RA1, RA2, RA3, or RA4 radios
(Kit # 5000-8750)
Challenger, and 300; 2017 Pacifica
INSTALLATION INSTRUCTIONS
Tools & Supplies Needed:
Electrical tape
Zip ties
Plastic panel removal tools
Drill with 1 1/8" step bit or hole saw
Screwdriver
Page 1 of 9
GS
Advertisement
Related Manuals for BrandMotion 5000-8750
Summary of Contents for BrandMotion 5000-8750
-
Page 1: Safety Precautions
• Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video, please visit www.brandmotion.com 5000-8750 Instructions 02-22-17.docx... -
Page 2: Installation Instructions
The radio will NOT function without either the 5000-8750 module or the 6-to-4 pin jumper installed. Set DIP switches to match the diagram below. Remove radio and install provided 5000-8750 T-harness. You will need to remove the 6-to-4 pin jumper from the T-harness and replace it with the provided 5000-8750 module. Connect module and harness BEFORE connecting radio. - Page 3 Remove the factory brackets and use the screws that come with the CD Player to attach the provided brackets to the housing and into the player. 2. Remove center console/cup holders, radio bezel, and radio. 3. Use provided template to drill hole for wiring. 5000-8750 Instructions 02-22-17.docx Page 3 of 9...
- Page 4 Make sure to check clearance on opposite side of console. 5. Finished CD player mounting should look like the picture below: 5000-8750 Instructions 02-22-17.docx Page 4 of 9...
- Page 5 3. Open the bin (marked “2” in the picture below) and use a trim stick to remove the media hub bezel. 4. Remove the six screws (marked as “2” in the picture below) and drop the bin (marked as “1” in the picture below) down to remove. 5000-8750 Instructions 02-22-17.docx Page 5 of 9...
- Page 6 13. Reinstall bin sides, reinstall bin in dash and route wiring behind radio. (See step 3 for radio removal.) 14. Leave sufficient slack in wire to allow bin to open and close without pinching or stretching wire. 5000-8750 Instructions 02-22-17.docx Page 6 of 9...
- Page 7 MAKE SURE TO CHECK BOTH SIDES OF ALL SURFACES BEFORE DRILLING ANY HOLES OR USING SELF- DRILLING SCREWS. Example: RAM truck crew-cab, player mounted under rear seat: 5000-8750 Instructions 02-22-17.docx Page 7 of 9...
- Page 8 For 8.4-inch RA3 and RA4 radios, proceed to remove the back end of the radio and disconnect the main 52-pin connector. 3. Route wiring from the CD player and install T-harness behind radio. 5000-8750 module should be installed on the T-harness at this point.
- Page 9 8. If no “DISC” icon has appeared, repeat steps 4-6 one additional time. The 5000-8750 module MUST remain installed in the vehicle for continued operation of the add-on CD player. For additional assistance, contact Brandmotion Technical Support at 1-734-619-1250 and select option 2 twice.