Filling & Checking The Engine Oil - ALDI Workzone Titanium+ 62007 User Manual

Preparation Information
WARNING.
• Do not refill fuel tank (26) while engine is running or is hot.
• Check to ensure that the fuel drain (10) has been tightened and that fuel is
not leaking.
• Be careful not to admit dust, dirt, water or other foreign objects into the fuel.
• Wipe off spilt fuel thoroughly before starting engine.
• Ensure you DO NOT fuel the generator in close proximity to any open
flames, lit cigarettes, or hot objects.
• The generator should also be located in an open area with fresh air and NOT
in a confined area.
WARNING: Ensure the engine is switched off while undertaking
this task.
1. Remove the fuel tank cap (27) by rotating in an anticlockwise direction.
2. Remove the fuel tank inlet filter (24) and ensure it is clean and free of debris.
Check the level of fuel is sufficient.
3. If the fuel tank inlet filter (24) was removed to check the fuel level, ensure it
is replaced back before adding fuel.
4. To add fuel, pour the unleaded fuel from an approved fuel container into the
fuel tank (26). As fuel expands, DO NOT FILL to the lip of the tank. Maximum
fill is to the top of the fuel tank inlet filter (24) rim.
5. Replace fuel tank cap (27) turning in a clockwise direction to lock.
Filling and checking the Engine oil
The engine of this generator is NOT filled with oil when unpacked.
Prior to starting the engine ensure the oil tank is filled with SAE 10W-30
4 stroke oil. For the first time fill the engine should be filled with 550ml
(+/-10%) of SAE 10W-30 oil. We recommend GARDENLINE® Full Synthetic
4 Stroke Oil.
NOTE: Damage to the engine is not covered under warranty if the engine is
run with insufficient oil.
NOTE: Ensure the fuel tank cap (27) is secure before attempting to add oil.
18
e-mail: help@powertoolsupport.com
MODEL: №. EP2800i • 09/2018 • 62007
Digital Inverter Generator with Pure Sine Wave
AFTER SALES SUPPORT
1800 909 909
Digital Inverter Generator with Pure Sine Wave
1. Before checking or refilling oil, be sure the
2. Remove the oil filler cap/dipstick (12)
3. If the oil level is close to or below the lower level line, refill using the supplied
4. If the oil is contaminated or has discoloured, ensure you change the oil.
AFTER SALES SUPPORT
(toll free) (toll free)
generator is put on a stable and level surface,
ensuring the engine has been switched OFF.
When filling with oil you can lift the generator
approximately 100 mm at the front (Fig G),
however the generator must be sitting flat back on
its feet when checking the level of oil using the oil
filler cap/dipstick (12).
Make sure you check the capacity of fuel tank
before checking the oil level. The fuel tank
(26) should be less than 50% full when the
generator is tilted by 100mm to fill the oil
reservoir, or fully drained if the generator is
tilted more than 100mm.
by rotating the cap in an anti-clockwise
direction, and wipe all oil residue off the oil
filler cap/dipstick (12) with a clean rag.
Re insert the oil filler cap/dipstick (12) and
thread the cap fully in position.
Then remove the oil filler cap/dipstick (12) by rotating in an anti clockwise
direction and view the oil level on the oil filler cap/dipstick (12).
oil bottle (32) with 4 stroke oil to the upper level line (Fig H).
Do not use the generator when the oil level is close to the low level. Fill the
oil tank before use each time.
Replace the oil filler cap/dipstick (12). DO NOT start the generator with the
oil Filler cap/dipstick (12) not firmly replaced.
NOTE: This engine is fitted with a low oil indicator light (4). If the oil level
is too low the engine will stop operating or the engine will not start. It is
advised to check the oil level each time the generator is used and fill to the
upper mark on the oil filler cap/dipstick (12) by the above method.
Do NOT over fill.
1800 909 909
Preparation Information
G.
H.
UPPER
MARK
LOWER
MARK
19
e-mail: help@powertoolsupport.com
MODEL: №. EP2800i • 09/2018 • 62007