Advertisement
2.
Open the ceiling clip so that it is wider
than the width of the T-bar.
3.
Move the ceiling clip so that it is appropriate for the T-bar width.
4.
Fix the ceiling clip in place by
tightening the 4 designated screws.
Screws for fixing
the ceiling clip
5.
Fix the T-bar in place by fastening
the screws (total of 2) that are on
the ceiling clip.
If the T-bar size of the ceiling is 15 mm,
24 mm or 38 mm, the position to fix the
ceiling clip can be checked from the
bottom surface of the mount bracket.
If the T-bar size is unknown, push the
ceiling clip to check the fixing positions.
6.
Pull out a LAN cable through a hole on the
ceiling and connect it to an Ethernet port
(PoE) on the back side of the WEA524i.
Exterior of the ceiling
If PoE is not supported, connect the power adapter to the DC input on the
back side of the WEA524i.
7.
Align the WEA524i with the
3 holes on the mount bracket
and then turn clockwise to fix
it in place. Clean up the ceiling
and other cables.
Installation on Walls
1.
Remove the holding tape that was
attached to fix the ceiling clip.
Holding tape
2.
Remove the ceiling clip from the mount bracket.
3.
Place the mount bracket on the wall.
Mark and drill 4 screws in appropriate spots.
Screws for
fixing T-bar
Interior of the ceiling
4.
Use a hammer to insert
4 plastic anchors into the
drilled holes on the wall.
Align the inserted plastic
anchors and the screw holes
of the bracket.
Fix the bracket to the wall
by fastening four M4 × L28
screws.
5.
Insert a LAN cable into the Ethernet port
(PoE) on the back side of the WEA524i.
If PoE is not supported, connect
the power adapter to the
DC input on the back of the
WEA524i.
Installing Anti-Theft Lock Cable
When installing the WEA524i in a public place, it is recommended to use
anti-theft lock cables to prevent any loss. (An anti-theft lock cable can be
purchased separately and a variety of products can be found in the market.)
1. Connect the anti-theft lock cable to the WEA524i.
2. Turn the lock cable key to lock the cable.
3. Remove the key from the lock cable and keep it in a separate location.
Using the anti-theft Torx screws
The WEA524i can be prevented from being stolen when tightening the Torx
screws as shown below. (Torx screws can be easily tightening when they
are fixed to the mount bracket before assembling the AP product.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
The 5150-5250 MHz band is restricted to indoor use only. (Canada)
The 5150-5350 MHz band is restricted to indoor use only. (Europe)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
RF Radiation Exposure Statement:
This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 50 cm between the
radiator and your body. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
RSS-102 RF Exposure
L'antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de
au moins 50 cm entre la source de radiation (l'antenne) et toute personne physique.
Cet appareil ne doit pas être installé ou utilisé en conjonction avec une autre antenne ou émetteur.
Should the AP be installed in a ceiling with ventilation, the AP Ethernet port
must be horizontally placed.
This product is RoHS compliant.
Regulatory Information
"Hereby, Samsung Electronics declares that the WEA524i is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet address:
http://www.samsungdocs.com, go to Search Product and enter the model name."
The wall
or
http://www.samsungenterprise.com
Part No.: EC68-00233A (Ver.1.0)
Advertisement
