Landa MHC3-25124 Operator's Manual page 27

REF PART NO.
24 8.911-227.0
25 8.912-699.0
26 8.755-626.0
27 8.914-946.0
28 8.914-947.0
29 8.914-952.0
30 8.914-960.0
31 8.914-962.0
32 8.914-969.0
33 8.914-972.0
34 8.932-992.0
- 9.803-308.0
35 9.802-066.0
36 8.916-090.0
37 8.900-282.0
38 8.940-051.0
39 9.800-002.0
40 9.800-006.0
41 9.800-008.0
42 9.800-021.0
43 9.803-475.0
44 9.800-049.0
45 9.802-013.0
46 9.802-041.0
47 9.802-043.0
48 9.196-012.0
49 9.802-053.0
50 9.802-054.0
51 9.802-071.0
52 9.802-089.0
53 9.802-531.0
- 9.803-835.0
54 9.802-125.0
55 8.707-020.0
56 9.802-146.0
57 9.802-152.0
58 9.802-153.0
59 9.802-154.0
60 9.802-170.0
61 9.803-559.0
62 9.802-193.0
63 9.802-207.0
64 8.709-069.0
QTY
2 AXLE, 5/8" X 28.5"L
4 STRAP, FUEL TANK W/HOLE
1 INSULATION, BLANKET-NO FOIL
1 BOTTOM WRAP ASSEMBLY
2 ASSEMBLY, AXLE
1 ASSY, HORIZ MHC FRAME, -07
1 PANEL, SIDE COVER
1 COIL. MHC DURA, 14.5" DIA SCH 80"
1 SS TOP WRAP
1 PANEL, CONTROL SIDE
4 MOUNT, RUBBER VIBRATION 3/8", 70 DURO
4 MOUNT, RUBBER VIBRATION 5/16" 70 DURO
1 PAD, SOFT RUBBER
2 LABEL, LANDA LOGO
1 LABEL, RPM FACTORY SET
1 LABEL, SKID OP INSTRUCTIONS
1 LABEL, USE ONLY KEROSENE
2 LABEL, "HOT/CALIENTE" W/ARROWS WARNING
1 LABEL, DANGER COOL ENGINE
1 LABEL, HOT WATER OUTLET
1 LABEL, OP INSTRUCTION, MT
1 LABEL, MANF CLEANING
1 NIPPLE, 1/2" X 2-1/2", GALV SCH 80
1 ELBOW, 3/8" STL, STREET 45° MXF
1 ELBOW, 1/2 JIC X 1/2 FEM 90°
1 SCREW, 10-24 X 1/4"
2 BUSHING, RUBBER, NITRILE
1 ELBOW, FUEL TANK ZINC
33" TRIM, 750B2 X 1/16, BLACK
1 CAP, FUEL TANK, PLASTIC H60-AV
1 REGULATOR, VOLTAGE, 15V
1 REGULATOR/RECTIFIER 18 AMP
1 PLUG, 1/4" JIC
1 PUSH-ON, 1/2" MPT X 3/4 BARB
1 SWIVEL, 1/2" MP X 3/4" GHF W/STRAINER
1 SWIVEL, 3/4" JIC FEM, PUSH-ON
1 SWIVEL, 1/4" JIC FEM, PUSH-ON
1 PLUG, PUSH-ON, OIL DRAIN, HONDA
1 COUPLER, 3/8 PLUG, FEM STEEL
1 CLAMP,SCREW, 9/16"W, 1-1/4"D, SS
15" GASKET, NEOPRENE,
1 CLAMP, ROUND, 0.687 DIA
6 CLAMP, SCREW 5/16"W, 1/4-5/8" D, SS
Landa MHC 9.800-950.0 - V
DESCRIPTION
Landa MHC
NOTES
(HONDA)
(ROBIN)
(PULL START)
(ELECTRIC START)
27