Page 1
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. LXC706 Genset Controller User Manual Ver1.1 Date: 2014/03/20 LXC706 SERIES Software version Date Versio Note 2013-05-10 Original release. 2014-03-20 Added USB interface for directly connecting to PC. LXC706 Product User Manual Dongguan Tuancheng Automation Equipment Co.,Ltd.
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. 1. SUMMARY The Module LXC706 is an small Automatic Engine Control Module. It selects 3 kinds of working state(Manual, Auto, Stop), can pass panel light touch buttons artificially start/stop genset, also can...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. With 3 working state: manual, automatic, stop. Through the software setting of controllers can be set to the engine controller (not choose the power voltage input), suitable for control of pump unit.
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. Working Conditions Temperature:(-25~+70)ºC Relative humidity:(20~90)% Storage Conditions Temperature:(-30~+80)ºC IP55:When waterproof rubber seal installed between the controller and panel fascia Protection Level IP42:When waterproof rubber seal is not installed between the controller and panel fascia Object:input/output/power...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. 5.2. LED ICON Symbol Defined Symbol Defined High Temperature Automatic state Low Oil Press Stop state Over Speed Manual states Under speed Generator voltage Emergency Stop Battery voltage High voltage Amount of fuel...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. Oil pressure,Water temperature Liquid level %, Total running time Parameter Settings 5.4. OPERATION Module has three states: stop state 、man state 、auto state 5.4.1. Man Start When push Man start button ,preheat will first output, and start preheat delay, when preheat delay is end, fuel output 1 second, preheat output will stop, and crank output is start.Here engine...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. NOTE: During the starting delay period, the fuel output disconnect. 3 seconds after entering the starting delay process, pre-heat and ETS output.After the end of the starting delay period, ETS output disconnect. Fuel output and pre-heat output disconnect before starting.
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. Emergency Stop: When emergency stop input, ETS solenoid stop immediately output, and then fuel disconnect, preheat and start signal emit emergency stop alarm signal. Gen Over Voltage: When the continuous sampling voltage higher than the preset value, at ...
Page 10
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. This is the amount of time that the start Idle speed is Start idle time (0-3600)S held active.These allow the engine to hold low speed. Warming up (0-3600)S delay Cooling delay...
Page 11
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. When battery voltage has fallen below the set value Battery Under and remains for 20s, It will initiate a warning alarm Voltage (4.0-30.0)V 8.0V signal. Only warning and not to shutdown the (Warning)...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. Disconnect When engine speed higher than the set value, starter (0-3000)RPM 360RPM Engine Speed will be disconnected. Disconnect Oil When generator oil pressure higher than the set value, (0-400)kPa 200kPa Pressure starter will be disconnected.
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. When this signal is effective and normal operation, If the temperature is too high, controller high-speed When cooling delay until after the downtime; When this signal temperature is too is invalid, If there is high temperature, the controller high downtime directly to the high-speed stop.
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. 8. CONDITIONS OF CRANK DISCONNECT Pictured above,select the desired options,can be selected or not selected There are 4 conditions to make starter disconnected with engine,that is,speed sensor, generator frequency ,Charge D + and engine oil pressure. They all can be used separately. We...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. 5) press the enter the parameter setting state, the first digit flashing, set of numerical methods with the same password input method. Password input interface: Parameter Settings interface: Matters needing attention:...
LXC706 Series Genset Controller Dongguan Tuancheng Automation Equipment Co.,Ltd. Terminal 10(L)、11(N):Alternator Input. Terminal 12(Idle Output):Idle speed control output port (B+,1A). Terminal 13(Stop Output):ETS output (B+ ,1A). Terminal 14(Configurable Output3):Configurable output, (B+, 1A). Terminal 15( D+):Connect to charging starter’s D+ terminal. If there is no this terminal, then be hang up.