RFSAI-61B
Wireless switch unit with the input
EN
Vezeték nélküli kapcsolóegység bemenettel
HU
Characteristics /
Jellemzők
• The switching unit with 1 output channel is used for controlling appliances and lights. It is pos-
sible to connect the existing button to the internal terminal in the wiring.
• They can be combined with detectors, controllers, iNELS RF Control or system components..
• The BOX design lets you mount it right in an installation box, a ceiling or controlled appliance cover.
• It enables connection of the switched load up to 16A (4.000 W).
• Function: button, impulse relay and time function of delayed start or return with time setting
range of 2s-60min.
• External button is programmed as a wireless button.
• Input is not galvanic isolated!
• The switching unit may be controlled by up to 25 channels (1 channel represents 1 button on
the controller).
• The programming button on the unit is also used for manual control of the output.
• Memory status can be pre-set in the event of a power failure.
• For components labelled as iNELS RF Control
via the RFAF/USB service device.
• Range up to 200 m (in open space), if the signal is insufficient between the controller and unit,
use the signal repeater RFRP-20 or protocol component RFIO
• Communication frequency with bidirectional protocol iNELS RF Control (RFIO
Assembly /
Telepítés
mounting in an installation box
(even under the existing button / switch)
telepítés kötő- vagy szerelvénydobozba
Connection /
Bekötés
RFSAI-61B/230V
RFSAI-61B/120V
Radio frequency signal penetration through various construction materials /
A rádiófrekvenciás jel átvitele különböző építőanyagokon keresztül
☺
☺
☺
For more information, see "Installation manual iNELS RF Control":
http://www.elkoep.com/catalogs-and-brochures
ELKO EP Hungary Kft. | Hungária krt. 69 | 1143 Budapest | Magyarország | e-mail: info@elkoep.hu | Technikai támogatás: +36 1 40 30 132
Made in Czech Republic
2
2
(RFIO
), it is possible to set the repeater function
2
that support this feature.
2
).
mounting into the light cover
beépítés a fényforrás burkolata alá
L
N
☺
☺
ELKO EP, s.r.o. | Palackého 493 | 769 01 Holešov, Všetuly | Czech Republic | e-mail: elko@elkoep.com | Support: +420 778 427 366
www.elkoep.com / www.elkoep.hu
• A kapcsolóegység egy kimeneti csatornával rendelkezik, mely felhasználható készülékek, alj-
zatok, világítások, stb. kapcsolására. Lehetőség van külső vezérlő nyomógomb bekötésére is.
• Kombinálható az iNELS RF Control rendszer Detektoraival, Vezérlőivel vagy Rendszeregységeivel.
• A BOX kivitel lehetővé teszi a telepítést közvetlenül egy szerelvénydobozba, álmennyezetre
vagy a kapcsolt készülék burkolata alá.
• Kapcsolt terhelés max. 16A (4000 W).
• Funkciók: nyomógombkövetés, impulzusrelé, be- és kikapcsolás, késleltetett be-és kikapcsolás,
ahol a késleltetési időtartamok 2mp-60p között állíthatók.
• A külső nyomógomb a vezeték nélküli nyomógombokkal megegyezően programozható.
• A bemenet nincs galvanikusan leválasztva.
• Egy egység akár 25 csatornáról is vezérelhető (1 csatorna 1 gomb a vezérlőn).
• A készülék programozó gombja a kimenet kézi működtetésére is használható.
• Beállítható memóriafunkció áramszünet esetére.
• Az egységeknél beállítható a jelismétlő (repeater) funkció az RFAF/USB szerviz eszközön keresztül.
• Hatótávolsága 200 m (nyílt terepen), amennyiben a vezérlő és az egységek közötti kommunikáció nem
megfelelő, használható az RFRP-20 jelismétlő vagy az RFIO
támogatják ezt a funkciót.
• Kommunikáció kétirányú iNELS RF Control
RFSAI-61B/24V
12-24 V AC/DC
60 - 90 %
80 - 95 %
wooden structures
brick walls
with plaster boards
fa és gipszkarton
téglafal
szerkezetek
Részletesebb információk az iNELS RF Control telepítési kézikönyvében:
http://www.elkoep.com/catalogs-and-brochures
2
protokollal rendelkező egységek, amelyek
2
protokollal (RFIO
ceiling mounted
telepítés álmennyezetre
L
N
20 - 60 %
0 - 10 %
reinforced
metal partitions
concrete
vasbeton
fém válaszfalak
02-56/2016 Rev.5
2
).
80- 90 %
common glass
normál üveg
1/6