This Unit; Power Cord; Power Amp; Installation - Pioneer DEH-S6120BS Operation Manual

− Disconnect the negative terminal of the battery
before installation.
− Secure the wiring with cable clamps or adhesive
tape. Wrap adhesive tape around wiring that
comes into contact with metal parts to protect
the wiring.
− Place all cables away from moving parts, such as
the shift lever and seat rails.
− Place all cables away from hot places, such as
near the heater outlet.
− Do not connect the yellow cable to the battery
by passing it through the hole to the engine
compartment.
− Cover any disconnected cable connectors with
insulating tape.
− Do not shorten any cables.
− Never cut the insulation of the power cable of
this unit in order to share the power with other
devices. The current capacity of the cable is
limited.
− Use a fuse of the rating prescribed.
− Never wire the negative speaker cable directly
to ground.
− Never band together negative cables of multiple
speakers.
• When this unit is on, control signals are sent
through the blue/white cable. Connect this cable
to the system remote control of an external power
amp or the vehicle's auto-antenna relay control
terminal (max. 300mA 12 V DC). If the vehicle is
equipped with a glass antenna, connect it to the
antenna booster power supply terminal.
• Never connect the blue/white cable to the power
terminal of an external power amp. Also, never
connect it to the power terminal of the auto
antenna. Doing so may result in battery drain or
a malfunction.
• The graphical symbol placed on the
product means direct current.

This unit

Microphone 3 m (9 ft. 10-1/8 in.)
SiriusXM Connect Vehicle Tuner input
Power cord input
Microphone input
Rear output (STD) or middle range output (NW)
Front output (STD) or high range output (NW)
Antenna input
Fuse (10 A)
Wired remote input
Hard-wired remote control adapter can be
connected (sold separately).
Subwoofer output
SiriusXM Connect Vehicle Tuner (sold separately)

Power cord

Perform these connections when not connecting
a rear speaker or middle range speaker lead to a
subwoofer.
Perform these connections when using a subwoofer
without the optional amplifier.
Important
In the case of above, two 4 Ω subwoofers wired
in parallel will represent a 2 Ω load.
To power cord input
Left
Right
Front speaker (STD) or high range speaker (NW)
Rear speaker (STD) or middle range speaker (NW)
White
White/black
Gray
Gray/black
Green
Green/black
Violet
Violet/black
Black (chassis ground)
Connect to a clean, paint-free metal location.
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by the ignition
switch (12 V DC).
Blue/white
Connect to the system control terminal of
the power amp or auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Subwoofer (4 Ω)
When using a subwoofer of 2 Ω, be sure to
connect the subwoofer to the violet and violet/
black leads of this unit. Do not connect anything
to the green and green/black leads.
Not used.
Subwoofer (4 Ω) × 2
Orange/white
Connect to a car's illumination signal.
Power amp (sold
separately)
Perform these connections when using the optional
amplifier.
System remote control
Connect to blue/white cable.
Power amp (sold separately)
Connect with RCA cables (sold separately)
To rear output (STD) or middle range output
(NW)
Rear speaker (STD) or middle range speaker (NW)
To front output (STD) or high range output (NW)
Front speaker (STD) or high range speaker (NW)
To subwoofer output
Subwoofer

Installation

Important
• Check all connections and systems before final
installation.
• Do not use unauthorized parts as this may cause
malfunctions.
• Consult your dealer if installation requires drilling
of holes or other modifications to the vehicle.
• Do not install this unit where:
− it may interfere with operation of the vehicle.
− it may cause injury to a passenger as a result of
a sudden stop.