Table of Contents
Summary of Contents for Carrier I-Vu Link
- Page 1 ® ® CARRIER CORPORATION ©2019 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-394-01 · 1/24/2019...
- Page 2 Verify that you have the most current version of this document from www.hvacpartners.com or your local Carrier office. Important changes are listed in Document revision history at the end of this document. CARRIER CORPORATION ©2019. All rights reserved throughout the world. i-Vu is a registered trademark of Carrier...
-
Page 3: Table Of Contents
Contents Introduction .................................. 1 What is the i-Vu® Link? ............................1 Specifications ................................ 2 Safety considerations............................3 Mounting and wiring ..............................4 To mount the i-Vu® Link ............................4 To wire for power ..............................4 To wire CCN devices on Port S1 ......................... 5 To wire a third-party device .......................... -
Page 5: Introduction
Each i-Vu® Link can connect to up to 140 CCN devices and supports up to 500 integration points. The i-Vu® Link also stores trend data and time schedules for the CCN devices that it is connected to. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 6: Specifications
A low battery is indicated by the Battery Low LED or a low battery alarm in the i- Vu CCN Plus/Pro application, a touchscreen device, and Field Assistant. Real-time clock Battery-backed real-time clock keeps track of time in event of power failure i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 7: Safety Considerations
Class A Safety considerations WARNING Disconnect electrical power to the i-Vu® Link before wiring it. Failure to follow this warning could cause electrical shock, personal injury, or damage to the controller. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 8: Mounting And Wiring
Status LED will display 8 for about 5 seconds and then reverts to 0, until controllers have been found and downloaded. There is a chase pattern when the router is running with no errors. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 9: To Wire Ccn Devices On Port S1
Turn on the i-Vu® Link's power. For... Use i-Vu® Link port... Wire Carrier ...to third-party Set the port's jumper(s) on terminal... device terminal i-Vu® Link EIA-232 EIA-232 Signal Ground EIA-485, Net+ EIA-485 2-wire Net- 2-wire i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... - Page 10 120 Ohm resistor across the + and - connectors of the furthest third-party controller. • A solid receive light on the i-Vu® Link indicates a wiring or polarity problem. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved...
-
Page 11: Configuring Ip For The I-Vu® Link
NOTE When the device manager is configured as the Gateway, it ignores the CCN/Ethernet Gateway IP address. In this case, leave the CCN/Ethernet gateway address at its default setting (0.0.0.0.). Repeat the above steps for each i-Vu® device manager used in the CCN system. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 12: Troubleshooting
Formatting the i-Vu® Link CAUTION This erases all archived information and user-configuration settings. You will have to reconfigure all custom settings. It is recommended to restore the factory defaults only under the guidance of Carrier Control Systems Support. To erase volatile memory data and restore factory default configuration settings: Turn off the i-Vu®... - Page 13 Obtain a Module Status Report (Modstat) and look for error messages. If you cannot determine the error from the Modstat, send a screenshot of the Modstat to Carrier Control Systems Support. NOTE To obtain a Module Status Report in the i-Vu CCN Plus/Pro interface, click the Main Menu button, then select Manual Command and type in modstat.
-
Page 14: To Replace The I-Vu® Link's Battery
Insert the new battery into the controller, matching the polarity of the battery you removed. Push the black clip back onto the battery until you hear both sides click in place. Download the i-Vu® Link. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 15: Compliance
BACnet Compliance Compliance of listed products to requirements of ASHRAE Standard 135 is the responsibility of BACnet International. BTL ® is a registered trademark of BACnet International. i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... -
Page 16: Document Revision History
Reworded Protection specification and added first paragraph. X-H-JS-O 8/6/14 Configuring the IP for the i-Vu® Link Corrected the Network Service Tool procedure by adding CCN C-TS-RD-E ENET Configuration. * For internal use only i-Vu® Link CARRIER CORPORATION ©2019 Installation Guide All rights reserved... - Page 18 CARRIER CORPORATION ©2019 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-394-01 · 1/24/2019...
Need help?
Do you have a question about the I-Vu Link and is the answer not in the manual?
Questions and answers