Installation Instructions ControlLogix AC (79-132V) Diagnostic Module (Catalog Number 1756-IA8D) See page: Prevent Electrostatic Discharge See Removal and Insertion Under Power (RIUP) Understand Compliance to European Union Directive Note the Power Requirements Identify the Module Components Install the Module Key the Removable Terminal Block/Interface Module Wire the Removable Terminal Block Assemble the Removable Terminal Block and the Housing Install the Removable Terminal Block onto the Module...
ControlLogix AC (79-132V) Diagnostic Module Wire the Removable Terminal Block Xv rÃurÃSU7Ãirs rÃvhyyvtÃvÃÃurÃqyrÃÃVrÃhÃ$ %ÃvpuÃ'Ãhvà syhiyhqrqÃp rq vr DHQPSU6IU)ÃQyyÃurÃuvtÃssÃsÃurÃSU7Ãirs rÃv vtÃÃÃÃÃÃÃÃà For the Spring Clamp RTB T vÃ& %Ãvpuà ÃhvÃyrtuÃÃv rà ÃSU7 Dr ÃurÃp rq vr ÃvÃurÃvr ÃuyrÃsÃurÃSU7 Dr ÃurÃv rÃvÃurÃrÃr vhyÃhqà rrÃurÃp rq vr 20863–M For the NEMA Screw RTB T vÃ$ %ÃvpuÃ'ÃhvÃyrtuÃÃv rà ÃSU7 Xv rÃurÃr vhy Publication 1756-5.5 - September 1999...
Page 8
ControlLogix AC (79-132V) Diagnostic Module Wiring example 1756-IA8D Not used L1-0 Loss of Field Power Daisy chain to L2-0 IN-0 other RTBs L2-0 IN-1 Group 0 Group 0 L2-0 IN-2 47kΩ, 1/2W, 5% resistor L2-0 IN-3 L2-1 IN-4 L2-1 IN-5 47kΩ, 1/2W, 5% resistor L2-1...
ControlLogix AC (79-132V) Diagnostic Module Assemble the Removable Terminal Block and the Housing 6yvtÃurÃt rÃhÃurÃiÃsÃrhpuÃvqrÃsÃurÃuvtÃvuÃurÃvqrÃrqtr sÃurÃSU7 TyvqrÃurÃSU7ÃvÃurÃuvtÃvyÃvÃhÃvÃyhpr Groove Side edge of the RTB Groove Strain relief area Side edge of the RTB 1756-TBNH RTB shown for reference 20852-M Publication 1756-5.5 - September 1999...
ControlLogix AC (79-132V) Diagnostic Module Check the Indicators UurÃvqvph ÃuÃvqvvqhyÃDPÃhÃryyÃs ÃrhpuÃvÃhqÃhÃivpy rqÃG@9Ãs à qyrÃÅPFÅà rqt rr ÃÃÃÃÃÃÃà 20927-M 9 vtÃr ÃÃhÃvqvph ÃrÃvÃqrÃÃUurÃÅPFÅÃvqvph à à rqÃs à ÃrpqÃhqà urà ÃÃsyhuvtÃt rrÃvsÃvÃuhÃhrqÃurÃrysrÃUurÃDPÃvqvph ÃvyyÃirÃhpvrÃs à hÃhvÃsÃ!Ãrpq This display: Means: Take this action: indicator: Steady green light The inputs are being None multicast and in normal operating state. Flashing green light The module has passed None internal diagnostics but is not...
ControlLogix AC (79-132V) Diagnostic Module 1756-IA8D Specifications Number of Inputs 8 (4 points/common) Module Location 1756 ControlLogix Chassis Backplane Current 100mA @ 5.1V dc & 3mA @ 24V dc (Total backplane power 0.58W) Maximum Power Dissipation (Module) 4.5W @ 60 Thermal Dissipation 15.35 BTU/hr On-State Voltage Range...
ControlLogix AC (79-132V) Diagnostic Module User Manual Publication 1756-6.5.8 Agency Certification (when product or packaging is marked) Class I Div 2 Hazardous Class I Div 2 Hazardous marked for all applicable directives marked for all applicable acts N223 Maximum wire size will require extended housing - 1756-TBE. Use this conductor category information for planning conductor routing as described in the system level installation manual.
Page 15
ControlLogix AC (79-132V) Diagnostic Module Explosion hazard! ATTENTION • Substitution of components may impair suitability for Class I, Division 2. • Do not replace components unless power has been switched off or the area is known to be non-hazardous. • Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
Page 16
Risque d’explosion ATTENTION • La substitution de composants peut rendre cet équipement inadapté à une utilisation en environnements de Classe 1, Division 2. • Couper le courant ou s'assurer que l’environnement est classé non dangereux avant de remplacer des composants. •...
Need help?
Do you have a question about the ControlLogix 1756-IA8D and is the answer not in the manual?
Questions and answers