Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Opticon CRD9823-RU
Summary of Contents for Opticon CRD9823-RU
- Page 1 CRD9823-RU Data Collector Cradle Specifications Manual...
- Page 2 Opticon assumes no liability for any direct, indirect, consequential or incidental damages arising out of use or inability to use both the hardware and software, even if Opticon has been informed about the possibility of such damages.
-
Page 3: Table Of Contents
Opticon CRD9823-RU Specifications Manual Contents 1. Abstract ..........................5 2. Overview ..........................5 3. Physical Features ......................... 5 3.1. Dimensions ........................5 3.2. Weight ........................... 5 4. Environmental Specifications ....................5 4.1. Operating Temperature and Humidity ................5 4.2. Storage Temperature and Humidity ................5 5. - Page 4 Opticon CRD9823-RU Specifications Manual Table of Figures Figure 1: DIP switch settings ..................... 8 Figure 2: Signal timing when software is configured ..............9 Figure 3: RS-232C cable ......................10 Figure 4: USB cable ........................ 10 Figure 5: Product label on the bottom of the cradle ..............11 Figure 6: Label on the back side of the cradle ................
-
Page 5: Abstract
USB (USB 2.0, CDC class virtual comm. port) or RS232C. The CRD9823-RU has three status LED’s, a red LED that indicates that the power is switched on, a green LED that blinks when the cradle receives data via IrDA and a yellow LED that blinks when data is received via USB or RS232. -
Page 6: Electrical Specifications
CRD9823-RU Specifications Manual 5. Electrical Specifications Only use dedicated Opticon approved AC adapters with this cradle. The output of such a AC adapter should be 6V/2A. It is not possible to power the cradle via USB. 5.1. Absolute Maximum Ratings... -
Page 7: Interface Specifications
Opticon CRD9823-RU Specifications Manual 6. Interface Specifications 6.1. External Interface Connector and Pin Assignment DC Power Supply Connector (EIAJ Type 3) 6.1.1. Signal Name Notes Inward +6 V Power supply +6 V Outward Ground Connector for USB on PC Side (USB Type B) 6.1.2. -
Page 8: Communications Interface
Opticon CRD9823-RU Specifications Manual 6.2. Communications Interface The baud rate can be configured via DIP switches on the bottom of the cradle. The baud rate can also be configured by using special software on the host. Baud rate Configuration using DIP switches 6.2.1. -
Page 9: Baud Rate Configured Using Software
Opticon CRD9823-RU Specifications Manual Baud Rate Configured Using Software 6.2.2. To allow configuration using software on the host computer, set SW4 to ON. The other DIP switches are not used when SW4 is ON. Baud Rate Remarks Line Line Edge 0 pulse 115.2 kbps... -
Page 10: Cables And Connectors
Opticon CRD9823-RU Specifications Manual 7. Cables and Connectors 7.1. RS232-C Cable Figure 3: RS-232C cable Type: Straight φ3.8 ±0.15 mm Diameter: Length: 1500 ±100, -0 mm Cores: 8 insulated wires, 1 conductive wire Left RJ50 (10-pin modular jack) Connectors Right DB9, female 7.2. -
Page 11: Labels
Opticon CRD9823-RU Specifications Manual 8. Labels The serial number shown below is affixed to the specified location on the cradle. 8.1. Product label Figure 5: Product label on the bottom of the cradle 8.2. Interface Label Figure 6: Label on the back side of the cradle... -
Page 12: Packaging Specifications
Opticon CRD9823-RU Specifications Manual 9. Packaging Specifications 9.1. Individual Packaging Put the cradle in a protective foam bag and place it in an individual packing box. Figure 7: Individual packaging specification... -
Page 13: Collective Packaging
Opticon CRD9823-RU Specifications Manual 9.2. Collective Packaging Figure 8: Collective packaging specification Note: The “RO” mark labeled on the package tray or package box guarantees that the applicable product has passed our test of RoHS restrictions compliance (the restriction of the use of certain hazardous substances in electrical and electronic equipment, 2002/95 EC). -
Page 14: Regulatory Compliance
Opticon CRD9823-RU Specifications Manual 10. Regulatory Compliance 10.1. EMC EN55022 EN55024 FCC Part 15 Subpart B Class B: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. -
Page 15: Safety Recommendations
Opticon CRD9823-RU Specifications Manual 11. Safety recommendations Handle this product carefully. Do not subject it to any of the following. Shock • Do not throw or drop the cradle. • Do not place heavy objects on the cables. Temperature Conditions •... -
Page 16: Mechanical Drawings
Opticon CRD9823-RU Specifications Manual 12. Mechanical Drawings Dimensions: W 98.5 x D 71.5 x H 67.0 mm Figure 9: Mechanical drawing Name DC jack DC jack for the dedicated AC adapter USB connector USB communication connector to the host computer...