Related Manuals for SENAO SL-2011CD-GP
Summary of Contents for SENAO SL-2011CD-GP
- Page 1 SL-2011CD-GP SL-2011CD-FP SL-2011CD-DP Antenna User Guide Before operating the unit, please read this manual thoroughly, and retain it for future reference.
-
Page 2: Installing The Antenna
Installing the Antenna 1. Introduction The Senao access point is designed to perform in a variety of environments. Implementing the antenna system can greatly improve coverage and performance. A good communication can only be achieved with the right antenna. The antenna kits comprise numerous components, including the antenna, connectors, mounting hardware, antenna cabling, and in certain product boxes. -
Page 3: Important Note
Figure 1-2: Directional Flat Panel Antenna (side view) 3. Antenna placement The advices below are basic concepts to install an antenna. The distance between the antenna and transceiver should be kept to a minimum to reduce signal loss. To operate at optimum efficiency, antenna cable should be kept as short as possible. - Page 4 4. Installing the 3dBi omni-directional antenna 4-1. Hardware Description The 3dBi omni-directional antenna is a broadband antenna for the 2.4GHz frequency band featuring an omni-directional pattern with a normal gain of 3dBi. Before you start installing the antenna, verify the following items in the antenna kits or in the product package.
- Page 5 Elements list Figure 1-3 4-2. Mounting the Omni-directional Antenna You can mount the 3dBi antenna to a ceiling for indoor use. This antenna uses vertical polarization that is the most common type of polarization for omni-directional antennas. ◆ Mounting to a ceiling In most cases, these installations require a large coverage area.
- Page 6 to the front of the bracket. 4. Feed the omni-directional antenna (item A) through the hole of the ferrule (item B) 5. Push the antenna through the ferrule (item B) to the end. Place screw (item E) to tighten the antenna. ：...
- Page 7 The hole of the antenna should be above the ferrul e Figure 1-4...
- Page 8 5. Installing the 7dBi Flat panel directional antenna 5-1. Hardware Description The 7dBi flat panel antenna is a broadband antenna for the 2.4GHz frequency band featuring a directional pattern with a normal gain of 7dBi. Before you start installing the antenna, verify the following items in the antenna kits or in the product package.
- Page 9 ◆ Assembly the stand To assembly the stand proceed following steps： 1. Put the strut (item D) through the hole of the panel for antenna (item B) and panel for wall (item C). 2. Place 2 screws (item F) through these two holes. 3.
- Page 10 Step 1 Step 2 Step 3 Step 4 Step 5 Step 6...
- Page 11 6.Installation Wireless PC card with one rubber antenna...
-
Page 12: Appendix A Specifications
Appendix A Specifications SL-2011CD General Radio Data Rate 11, 5.5, 2 and 1 Mbps, Auto Fall-Back 11 Mbps – 150m 5.5 Mbps – 200m Range (open environment) 2 Mbps – 250m 1 Mbps – 400m Operating Voltage 3.3V/5V EMC Certifications FCC Part 15, ETSI 300/328 Fully interoperable with IEEE802.11b Compatibility... -
Page 13: Physical Specifications
Environmental Temperature Range 0 to 50 C (operating) -20 to 80 C (storage) Humidity (non-condensing) 5% to 95% typical Physical Specifications Form Factor PCMCIA Type II PC Card Dimensions 118(L) mm x 54(W) mm x 7.5(H) mm Weight 40 g... - Page 14 Specifications 3dBi Omni-directional Antenna Mechanical Size H 390 mm(15.35 inches) Weight 370 g (13.05 ounces) Material Guide pipe : Aluminum alloy Bracket : Aluminum alloy Mounting method Using our antenna kits to mount to a ceiling Connector N-Female(reverse) Electrical Frequency 2400-2485 MHz Polarization Vertical...
-
Page 15: Appendix B Regulatory Compliance Information
Appendix B Regulatory Compliance Information Radio Frequency Interference Requirements FCC ID：NI3-SL-2011CD-ANT CANADA：xxxxxxx This device complies with Part 15 of FCC Rules and Canada RSS-210. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the SL-2011CD-GP and is the answer not in the manual?
Questions and answers