Sharp CD DHS1050P Operation Manual page 13

Timer and sleep operation (Remote control only) (continued)
1 minute or more
Daily timer
Start Stop
Timer playback
Before setting timer:
1 Check that the clock is set to the correct time. If it is
not set, you cannot use the timer function.
2 For timer playback: Plug in USB, dock iPod/iPhone,
load discs or tape to be played.
1
Press the ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
to select "ONCE" or "DAILY", and press the MEMORY
button. Set the clock to the correct time if "ONCE" or
"DAILY" does not appear.
4
Within 10 seconds, press the
"ONCE SET" or "DAILY SET", and press the MEMORY
button.
5
To adjust the hour, press the
press the MEMORY button.
6
To adjust the minutes, press the
then press the MEMORY button.
7
Set the time to fi nish as in steps 5 and 6 above.
8
To select the timer playback source (CD, TUNER, USB,
iPhone/iPod, TAPE or AUDIO IN), press the
button. Press the MEMORY button.
When you select the tuner, select a station by pressing
the or button, and then press the MEMORY
button. If a station has not been programmed, "NO
PRESET" will be displayed and timer setting will be
canceled.
10
Adjust the volume using the VOLUME control, and then
press the MEMORY button. Do not turn the volume up
too high.
11
Press the ON/STAND-BY button to enter the power
stand-by mode. The "TIMER" indicator lights up and
the unit is ready for timer playback.
12
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The "" or "DAILY" indicator will blink
during timer playback.
13
When the timer end time is reached, the system will
enter the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer operates at the same time every day. It
will continue until the daily timer setting is canceled.
Cancel the daily timer when it is not in use.
Once timer
Start Stop
or
or button to select
or button and then
or button and
5
4
3
2
1
MINI COMPONENT SYSTEM
CD-DHS1050P
REMOTE
TIMER
SENSOR
POWER
ON/ STAND-BY
OPEN / CLOSE
VOL.
VOL.
iPod/iPhone
5
CD
4
TUNER
(BAND) 3
TAPE
TUNING PRESET
2
AUDIO IN
USB
1
Notes:
When performing timer playback using another unit
connected to the USB terminal or AUDIO IN jack,
select "USB" or "AUDIO IN" in step 8.
This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not
turn on or off. To stop the timer playback, follow step
"Canceling the timer setting" of this page.
Checking the timer setting:
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 10 seconds, press the
"ONCE" or "DAILY", and press the MEMORY button.
3
Within 10 seconds, press the
select "ONCE CALL" or "DAILY CALL", and press the
MEMORY button.
Canceling the timer setting:
button
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 10 seconds, press the
"ONCE" or "DAILY", and press the MEMORY button.
3
Within 10 seconds, press the
"ONCE OFF" or "DAILY OFF", and press the MEMORY
button. Timer will be canceled (the setting will not be
canceled).
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To
reuse the same setting, perform the following operations.
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
or
2
Within 10 seconds, press the
"ONCE" or "DAILY", and press the MEMORY button.
3
Within 10 seconds, press the
"ONCE ON" or "DAILY ON", and press the MEMORY
button.
4
Press the ON/STAND-BY button to enter the power
stand-by mode.
Sleep operation
The iPod, Audio In, radio, CD, MP3/WMA disc, USB and
cassette tape can all be turned off automatically.
1
Play back the desired sound source.
2
Press the SLEEP button.
3
Within 10 seconds, press the SLEEP button repeatedly
to select the time and then press the MEMORY
button.
4
"SLEEP" will appear.
5
The unit will enter the power stand-by mode
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation fi nishes.
To confi rm the remaining sleep time:
1
While "SLEEP" is indicated, press the SLEEP button.
To cancel the sleep operation:
Press the ON/STAND-BY button while "SLEEP" is
indicated. To cancel the sleep operation without setting the
unit to the stand-by mode, proceed as follows.
1
While "SLEEP" is indicated, press the SLEEP button.
2
Within 10 seconds, press the SLEEP button repeatedly
to select "SLEEP OFF" and then press the MEMORY
button.
E-12
or
or
or
or
or
10 20 30 ....... 80
button to select
or button to
button to select
button to select
button to select
button to select
90