Setting The Clock (Remote Control Only); Timer And Sleep Operation (Remote Control Only); Listening To A Cassette Tape - Sharp CD DHS1050P Operation Manual

Listening to a cassette tape

Before playback:
For playback, use normal or low-noise
tapes for the best sound. (Metal or
CrO tapes are not recommended.)
2
Do not use C-120 tapes or poor-quality
tapes, as they may cause malfunctions.
Before loading a tape into the cassette compartment,
tighten the slack with a pen or a pencil.
Tape playback
1
Press the ON/STAND-BY button to turn the power on.
2
Open the cassette compartment
by pushing the area marked " ".
3
Load a cassette into the
TAPE compartment
the side to be played facing
toward you.
4
Press the TAPE / TUNER
button repeatedly to select
TAPE.
5
Press the (TAPE ) button to start playback.
Various tape functions
Main
Function
unit
Stop
Fast
forward/
rewind
Caution:
Before remove the cassette or changing from one tape
operation to another, press the
If a power failure occurs during tape operation, the
tape head will remain engaged with the tape and the
cassette door will not open. In this case, wait until the
power is restored.
Cleaning the tape-handling parts
Dirty heads, capstans or pinch rollers can cause poor
sound and tape jams. Clean these parts with a cotton
swab moistened with commercial head/pinch roller
cleaner or isopropyl alcohol.
When cleaning the heads, pinch rollers, etc., unplug
the unit which contains high voltages.
A Playback head
B Capstan
C Pinch roller
After long use, the deck's heads and capstans may
become magnetized, causing poor sound. Demagnetize
these parts once every 30 hours of playing/recording
time by using a commercial tape head demagnetizer.
Read the demagnetizer's instructions carefully before
use.
with
Remote
Operation
control
Press in the
TAPE
playback, fast
forward or fast
rewind mode.
Press in the
playback or stop
mode.
(TAPE ) button.
A
TAPE 1
Setting the clock (Remote control
only)
In this example, the clock is set for the 12-hour (AM 12:00)
display.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the MEMORY button.
4
Press the
24-hour display and then press the MEMORY button.
"AM 12:00"
"AM 0:00"
"0:00"
5
Press the
then press the MEMORY button.
6
Press the
and then press the MEMORY button.
Press the
time by 1 minute. Hold it down to change the time in
5-minutes intervals.
To confi rm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 10 seconds.
Note:
The "CLOCK" will appear or time will fl ash to confi rm the
time display when the AC power supply is restored after a
power failure or unplugging the unit. If incorrect, readjust
the clock as follows.
To readjust the clock:
Perform "Setting the clock" from step 1. If "CLOCK" does
not appear in step 3, step 4 (for selecting the 12-hour or
24-hour display) will be skipped.
To change the 12-hour or 24-hour display:
1
Clear all the programmed contents. [Refer to "Factory
reset, clearing all memory" on page 14 for details.]
2
Perform "Setting the clock" from step 1 onwards.
Timer and sleep operation (Remote
control only)
Once timer:
Once timer play works for one time only at a preset time.
Daily timer:
Daily timer play works at the same preset time every day.
For example, set the timer as a wake-up call every
morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen to a radio
program, and use the daily timer to wake up.
B
C
E-11
or button to select 12-hour or
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
or button to adjust the hour and
or button to adjust the minutes
or button once to advance the