Safety Instruction For your safety, please read the following instruction before you use the product. Serious injury or property loss may be caused by improper operations. Do not try to repair the product without guidance. Placement Do not place the unit on an unstable cart, stand, tripod, racket, table, or shelf. ...
Page 4
Humidity Do not expose machine in rain, damp or place near water. Ensure the indoor drying, cool. Ventilation Keep the ventilation openings clear. Ensure that the unit has enough space for ventilation around: left, right and back >10cm, top> 20cm. Earphone ...
Installation Bearing If the product is installed in a wall-mounted way, the bearing capacity of the surface for installation must be at least four times of the weight of the product. If the surface for installation is a wall or the ceiling of a building, the surface must be made of solid bricks, concrete or other materials with equal intensity.
Insert wall plugs into the mounting holes. Attach the mounting arms to the Push the self-tapping screws through the back of screen with the screws. bracket into the wall plugs and tighten the screws. Note: The horizontal and vertical distance of mounting holes on the back of screen must be within the required distance of bracket.
Handle facing outward Basic Operation Power on Power the interactive touch screen with the 100V-240V 50Hz/60Hz AC power supply. Connect the panel to the power supply. Press the rocker switch (on the bottom left in the rear of the panel) to enter standby mode.
Control Panel 2 3 4 5 6 7 8 9 10 11 12 Item Icon Function Description Power indicator: Press power button on the control panel. The power indicator turns green. Press power button on the control panel to enter the standby mode. The power indicator turns red.
Terminal Interface Terminal Interface Type 1 RJ45 IN USB-Touch HDMI IN VGA IN Audio IN USB 3.0 AV IN YPbPr IN AV OUT Earphone OUT SD CARD HDMI OUT RS232 SPDIF WIFI: antenna port Terminal Interface Type 2 RJ45 IN RJ45 OUT DP IN HDMI IN...
Remote Control Item Function Description Power on or standby mode Mute on/off Change channels or enter numbers Return to previous interface SLEEP: Set the sleep time NICAM: Nicam button ASPECT: Adjust picture aspect ratio Signal source selection Show the current signal source Up/down/right/left direction buttons OK: Confirm Show or hide menu...
Remote Control Area The effective receiving area is about 3 meters with 30° angle from vertical point to the left and right. And the effective receiving area is about 5 meters from the front of device. Note that the remote control signal receiver locates at the position of power indicator.
Connecting and Setting For safety, please do not connect any power supply before the external devices setup. 1. External Computer and Touch Connecting Audio IN VGA IN USB-Touch 1) Connect a VGA cable (15 pin) between the VGA and external PC. Connect an earphone cable between the PC and audio at the same time.
2. AV Connecting AV IN 1) Connect an AV cable with the device with AV-OUT (Yellow is Video, Red is Audio-R, White is Audio-L). 2) Plug the POWER cord and switch it on from the rear panel. 3) Press to turn on the panel.
Front HDMI/ HDMI 1/ HDMI 2 1) Connect a HDMI cable with the device with HDMI. 2) Plug the POWER cord and switch it on from the rear panel. 3) Press to turn on the panel. 4) Select Signal source to HDMI source according to the one you connected. 3.
AV-OUT 1) Connect an AV cable with the device. 2) Plug the POWER cord and switch it on from the rear panel. 3) Press to turn on the panel. AV-OUT outputs the picture and sound of AV source. 4. RS232 1) Connect a serial port cable with the device.
Page 16
RS232 code list There are two RS232 code lists. Please check your Android firmware version first and refer to corresponding list according to your Android firmware version. RS232 Code for Android Firmware QOMO_xxx_xxx_xxxxx_Vxx 6 bytes command Baud rate: 115200 Data bits: 8 Check bit: none Start code 99, Customer code (Public Version: XX = 23), Function ID code, Device ID code(It is generally 01, unless otherwise noted), Check code + Function ID code = FF, End code AA.
Page 17
Channel - |99 XX 1A 01 E5 AA Screenshot |99 XX 1B 01 E4 AA Screen Display |99 XX 1C 01 E3 AA Display ratio |99 XX 1E 01 E1 AA Sleep Mode |99 XX 1D 01 E2 AA Auto Adjustment |99 XX 1F 01 E0 AA |99 XX 22 01 DD AA Down...
Page 18
(Bidirectional) Set Signal Source 0x55 0x54 0x53 0x50 0x73 0x21 0x21 0x21 (DTV) Set Signal Source 0x55 0x54 0x53 0x50 0x73 0x21 0x21 0x21 (ATV) Set Signal Source 0x55 0x54 0x53 0x50 0x73 0x30 0x30 0x21 (Video 1) Set Signal Source 0x55 0x54 0x53...
Android Home Page Education Version Android home page consists of three parts as shown in above picture. Click on the toolbar or Press HOME button to enter the home page. 1. Click a signal source in part ① and its preview will be shown in part ②. Then click part ② to enter its corresponding signal source.
Business Version Android home page mainly contains three parts: Quick-access Apks, Time and Network Connection Status. Click on the toolbar or Press HOME button to enter the home page. 1. Click to open corresponding APK; Click to display all the APKs installed. 2.
Bottom-up Toolbar The toolbar can be invoked in any signal source interface. Swipe up from the bottom of screen and it will appear. Buttons Functions Click to enter PC source Back Return to previous interface Home Return to Android home page Switch or end the running programs Task Input...
Signal Source Selection There are three ways to select a signal source to display. Swipe your finger up from the bottom edge to bring up a toolbar then click Input. Press SOURCE button on the remote control. Press button on the front control panel.
Android Settings Click setting icon on home page to enter Android setting interface. 1. Common function: Click Common function to set Starting Channel, Sound, Wallpaper, ECO, Lock Screen and Factory Data Reset. Starting Channel: Start the Panel and enter the channel you set directly. ...
Page 25
2. Network and equipment: Click Network and equipment to set WLAN, Ethernet, Tethering& portable hotspot and Mcast. WLAN: Select an available wireless network AP and enter the password to be connected. Click and a menu pops up. Select “Advanced” for further setting. ...
Page 26
4. Language & input: Where you can change the system or keyboard language.
Page 27
5. Date & time: Where you can change time format, time zone and etc. 6. About: Click About to check network status, model, Android version, Kernel version and etc. Click Status and enter its page to get the Mac address.
Built-in PC Operation 1. Select PC signal source to enter PC interface. The following are three ways to select a signal source channel. Swipe your finger up from the bottom edge to bring up a toolbar then click input. ...
Menu When you switch to other signal sources like OPS, HDMI, VGA and etc, settings interface will be displayed as follows: Picture, Sound and Setting. Note that TV setting is disabled. Click an icon to set the option or press button on remote control to switch the options.
Annotation software - MagicBoard MagicBoard provides various functions like annotation, capture, quick-access Apps & Docs and etc. Click icon to enter whiteboard interface. And click icon to fold/unfold the toolbar. MagicBoard Interface Icons Functions Click to exit the program or Select to keep it running in the background Click “<”...
Page 31
1. Save file: Click icon to save the file. Check “Save to editable file” box so that you can reedit this file next time. You can open this editable file through DOC of File Management You have the option to save the file in PDF format and scan QR code to share the file. Note that you mobile device should be in the same network with Magicboard.
Page 32
3. Whiteboard running in the background: Click icon then click “Background” and the whiteboard will run in the background. Icon will appear on both sides. Click either of them to unfold the tools. Note that floating icons will float in every singal source for annotation.
Page 33
Annotation mode Save annotation as an image or scan QR code to share the annotation Enter the whiteboard Rectangular screenshot Window Shade Adjust volume...
Included Accessories Picture Name Quantity Remote control Battery (AAA) Pointer 1.8m power cable 3m HDMI cable 3m USB cable (A-B) Bracket Antenna sticks for PC and Android Warranty card...
No image is displayed or the Modify the color settings. image is black and white. Check the color system. This is the general user manual for all QOMO interactive touch screens. Some details may be different from the actual product.
Need help?
Do you have a question about the Journey 13 series and is the answer not in the manual?
Questions and answers